SUPER MICRO Computer 6014L-T Security Settings, Change Supervisor Password, Change User Password

Page 86

SUPERSERVER 6014L-T User's Manual

7-5 Security Settings

The AMI BIOS provides a Supervisor and a User password. If you use both pass- words, the Supervisor password must be set fi rst.

Change Supervisor Password

Select this option and press <Enter> to access the sub-menu, and then type in the password.

Change User Password

Select this option and press <Enter> to access the sub-menu, and then type in the password.

Clear User Password

Select this option and press <Enter> to access the sub menu. You can use the sub menu to clear the user password.

Boot Sector Virus Protection

This option is near the bottom of the Security Setup screen. Select "Disabled" to deactivate the Boot Sector Virus Protection. Select "Enabled" to enable boot sec- tor protection. When Enabled, AMIBOIS displays a warning when any program (or virus) issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The options are Enabled and Disabled.

7-18

Image 86
Contents Super Manual Revision Release Date March 6 Manual Organization PrefaceAbout This Manual Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup SMBBios AppendicesPage Chapter Introduction OverviewSerial ATA Serverboard FeaturesProcessors Memory PCI Expansion SlotsOther Features Onboard Controllers/PortsIntel E7520 Chipset System Block Diagram Serial ATA Subsystem Server Chassis FeaturesSystem Power Control PanelCooling System Rear I/O PanelEurope Contacting SupermicroHeadquarters Asia-PacificPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Serial ATA Drive Carrier LED Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions UnpackingInstalling the Serverboard Serverboard InstallationInstalling the Heatsink Brackets Processor and Heatsink Installation Installing the ProcessorsInstalled heatsink Installing the HeatsinksInstalled processor Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel I/O PortsMemory Support Installing MemoryDimm Installation See Figure PCI slots PCI card installationAdding PCI Cards Serverboard Details Super X6DLP-EG2 LayoutOnboard Indicators Description Jumper Description Default SettingConnector Description X6DLP-EG2 Quick ReferenceProcessor Power Connector Connector DefinitionsATX Power Connector Power LEDOverheat/Fan Fail LED Power Fail LEDNIC1/2 LEDs JLAN1/2 Ethernet Ports Reset ButtonPower Button Chassis IntrusionFan Headers Universal Serial Bus USB0/1Universal Serial Bus Headers Wake-On-LAN Speaker/Power LED/KeylockWake-On-Ring SMB Power I2 C ConnectorPower Fault ATX PS/2 Keyboard and PS/2 Mouse PortsExplanation Jumpers Jumper SettingsJLAN1/2 Enable/Disable Cmos ClearSMBus to PCI Slots VGA Enable/DisablePower Force On Watch DogJlan LEDs Onboard IndicatorsAlarm Reset System Status LEDOnboard LED Indicators DS1, DS5 Onboard LED Indicators DS7, DS8Parallel Port, Floppy, IDE and Sata Drive Connections Parallel Printer Port HeaderFloppy Connector Sata ConnectorsIDE Connectors IDE Drive Connectors Pin Definitions IDE1, IDE2Static-Sensitive Devices Chapter Advanced Chassis SetupPrecautions Tools RequiredControl Panel Chassis Front ViewSystem Fans Drive Bay Installation/RemovalAccessing the Drive Bays System Fan FailureSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives CD-ROM and Floppy Drive Installation Serial ATA BackplaneReplacing the Power Supply Power SupplyPower Supply Failure Page Introduction How To Change the Configuration DataChapter System Memory Main SetupProcessors CPU Configuration Sub-Menu Advanced SettingsConfigure Advanced CPU Settings System Time/System DateIDE Configuration Combined Mode OperationIDE Configuration Sub-Menu ATA Ports DefinitionBlock Multi-Sector Transfer LBA/Large ModeType A.R.T. For Hard disk drivesFloppy Configuration PCI/PnP ConfigurationPCI IDE BusMaster Allocate IRQ to PCI VGAPalette Snooping Offboard PCI/ISA IDE CardSuper IO Configuration Sub-Menu Advanced Chipset Settings Power Configuration Apci ConfigurationPCI/PCI Express Error Logging Watch Dog TimerPCI/PCI Error Logging Event Log ConfigurationPCI Express Configuration Remote Access ConfigurationMPS Configuration Redirection After Bios Post Remote AccessSerial Port Mode Sredir Memory Display DelayUSB Configuration System Health MonitorFan Speed Control Modes Boot SettingsSystem Fan Monitor Fan1 Speed to Fan6 SpeedsBios Settings Configuration Removable Drives Boot Device PriorityHard Disk Drives CD/DVD DrivesChange User Password Security SettingsChange Supervisor Password Clear User PasswordSaving Changes and Exit Load Optimal DefaultsExit Options Discarding Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes LED Indicators DS7/DS8 LED Post CodesAppendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Intel 6300ESB I/O Controller Hub Appendix C Software InstallationSerial ATA Sata Adaptec RAID Configuration Utility ARC Configuring Sata RAIDAdaptec Sata HostRAID Controller Driver Using the Array Configuration Utility ACU Managing Arrays Viewing Array PropertiesDeleting Arrays Creating ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array To initialize drives Deleting a Bootable ArrayInitializing Disk Drives Page Page Rebuilding Arrays To rebuild an arrayUsing the Disk Utilities To access the disk utilitiesExiting the Adaptec RAID Configuration Utility You can choose from the following optionsInstalling the ICH5R/6300 ESBDriver Installing Other Software Programs and Drivers Installing Additional DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications System Cooling WeightPower Supply System Input Requirements