SUPER MICRO Computer 6014L-T Connector Definitions, ATX Power Connector, Processor Power Connector

Page 48

SUPERSERVER 6014L-T User's Manual

5-9 Connector Definitions

ATX Power Connector

The main power supply connector on the X6DPL-EG2 meets the SSI EPS 12V specifi cation. See the table on the right for pin defi nitions.

Note: You must also connect the processor power connector (PW2, below.)

Processor Power Connector

In addition to the Primary ATX power connector (above), the 12V processor power connector at PW2 must also be connected to your power supply to provide adequate power to the system.

ATX Power 24-pin Connector

Pin Definitions (PW1)

Pin#

Defi nition

Pin #

Defi nition

13

+3.3V

1

+3.3V

14

-12V

 

+3.3V

2

15

COM

 

COM

3

16

PS_ON

 

+5V

4

17

COM

 

COM

5

18

COM

 

+5V

6

19

COM

 

COM

7

20

Res (NC)

 

PWR_OK

8

21

+5V

 

5VSB

9

22

+5V

10

+12V

23

+5V

11

+12V

24

COM

12

+3.3V

 

 

 

 

Secondary Power

Connector

Pin Definitions (PW2)

Pins

Defi nition

1 through 4

Ground

5 through 8

+12V

 

 

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin defi nitions.

Power LED

The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table on the right for pin defi nitions.

NMI Button

Pin Definitions (JF1)

Pin# Defi nition

19Control

20Ground

Power LED

Pin Definitions (JF1)

Pin# Defi nition

15Vcc

16Control

5-12

Image 48
Contents Super Manual Revision Release Date March 6 Preface About This ManualManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup SMBBios AppendicesPage Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsOther Features Onboard Controllers/PortsIntel E7520 Chipset System Block Diagram Server Chassis Features System PowerSerial ATA Subsystem Control PanelCooling System Rear I/O PanelContacting Supermicro HeadquartersEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Serial ATA Drive Carrier LED Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingServerboard Installation Installing the Heatsink BracketsInstalling the Serverboard Processor and Heatsink Installation Installing the ProcessorsInstalling the Heatsinks Installed processorInstalled heatsink Removing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel I/O PortsInstalling Memory Dimm Installation See FigureMemory Support PCI card installation Adding PCI CardsPCI slots Serverboard Details Super X6DLP-EG2 LayoutJumper Description Default Setting Connector DescriptionOnboard Indicators Description X6DLP-EG2 Quick ReferenceConnector Definitions ATX Power ConnectorProcessor Power Connector Power LEDPower Fail LED NIC1/2 LEDsOverheat/Fan Fail LED Reset Button Power ButtonJLAN1/2 Ethernet Ports Chassis IntrusionUniversal Serial Bus USB0/1 Universal Serial Bus HeadersFan Headers Speaker/Power LED/Keylock Wake-On-RingWake-On-LAN Connector Power FaultSMB Power I2 C ATX PS/2 Keyboard and PS/2 Mouse PortsJumper Settings JLAN1/2 Enable/DisableExplanation Jumpers Cmos ClearVGA Enable/Disable Power Force OnSMBus to PCI Slots Watch DogOnboard Indicators Alarm ResetJlan LEDs System Status LEDOnboard LED Indicators DS1, DS5 Onboard LED Indicators DS7, DS8Parallel Port, Floppy, IDE and Sata Drive Connections Parallel Printer Port HeaderFloppy Connector Sata ConnectorsIDE Connectors IDE Drive Connectors Pin Definitions IDE1, IDE2Chapter Advanced Chassis Setup PrecautionsStatic-Sensitive Devices Tools RequiredControl Panel Chassis Front ViewDrive Bay Installation/Removal Accessing the Drive BaysSystem Fans System Fan FailureSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives CD-ROM and Floppy Drive Installation Serial ATA BackplanePower Supply Power Supply FailureReplacing the Power Supply Page How To Change the Configuration Data ChapterIntroduction Main Setup ProcessorsSystem Memory Advanced Settings Configure Advanced CPU SettingsCPU Configuration Sub-Menu System Time/System DateCombined Mode Operation IDE Configuration Sub-MenuIDE Configuration ATA Ports DefinitionLBA/Large Mode TypeBlock Multi-Sector Transfer A.R.T. For Hard disk drivesFloppy Configuration PCI/PnP ConfigurationAllocate IRQ to PCI VGA Palette SnoopingPCI IDE BusMaster Offboard PCI/ISA IDE CardSuper IO Configuration Sub-Menu Advanced Chipset Settings Power Configuration Apci ConfigurationWatch Dog Timer PCI/PCI Error LoggingPCI/PCI Express Error Logging Event Log ConfigurationRemote Access Configuration MPS ConfigurationPCI Express Configuration Remote Access Serial Port ModeRedirection After Bios Post Sredir Memory Display DelayUSB Configuration System Health MonitorBoot Settings System Fan MonitorFan Speed Control Modes Fan1 Speed to Fan6 SpeedsBios Settings Configuration Boot Device Priority Hard Disk DrivesRemovable Drives CD/DVD DrivesSecurity Settings Change Supervisor PasswordChange User Password Clear User PasswordLoad Optimal Defaults Exit OptionsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description LED Indicators DS7/DS8 LED Post CodesAppendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C Software Installation Serial ATA SataIntel 6300ESB I/O Controller Hub Configuring Sata RAID Adaptec Sata HostRAID Controller DriverAdaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACU Managing Arrays Viewing Array PropertiesDeleting Arrays Creating ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array Deleting a Bootable Array Initializing Disk DrivesTo initialize drives Page Page Rebuilding Arrays To rebuild an arrayUsing the Disk Utilities To access the disk utilitiesExiting the Adaptec RAID Configuration Utility You can choose from the following optionsInstalling the ICH5R/6300 ESBDriver Installing Other Software Programs and Drivers Installing Additional DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications Weight Power SupplySystem Cooling System Input Requirements