SUPER MICRO Computer 6014L-T user manual Chapter System Interface, Control Panel Buttons

Page 29

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the Serial ATA drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of speciﬁ c components. There are also two but- tons on the chassis control panel. This chapter explains the meanings of all LED indicators and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are two push-button buttons located on the front of the chassis: a reset but- ton and a power on/off button.

RESET: The reset switch reboots the system.

POWER: This is the main power switch, which is used to apply or turn off the main system power. Turning off system power with this button removes the main power but keeps standby power supplied to the system.

3-1

Image 29

Contents Super Manual Revision Release Date March 6 Manual Organization PrefaceAbout This Manual Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Serverboard Setup System SafetySMB Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram System Power Server Chassis FeaturesSerial ATA Subsystem Control PanelRear I/O Panel Cooling SystemHeadquarters Contacting SupermicroEurope Asia-PaciﬁcPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LED Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard UnpackingInstalling the Serverboard Serverboard InstallationInstalling the Heatsink Brackets Installing the Processors Processor and Heatsink InstallationInstalled heatsink Installing the HeatsinksInstalled processor Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables I/O Ports Connecting the Control PanelMemory Support Installing MemoryDimm Installation See Figure PCI slots PCI card installationAdding PCI Cards Super X6DLP-EG2 Layout Serverboard DetailsConnector Description Jumper Description Default SettingOnboard Indicators Description X6DLP-EG2 Quick ReferenceATX Power Connector Connector DeﬁnitionsProcessor Power Connector Power LEDOverheat/Fan Fail LED Power Fail LEDNIC1/2 LEDs Power Button Reset ButtonJLAN1/2 Ethernet Ports Chassis IntrusionFan Headers Universal Serial Bus USB0/1Universal Serial Bus Headers Wake-On-LAN Speaker/Power LED/KeylockWake-On-Ring Power Fault ConnectorSMB Power I2 C ATX PS/2 Keyboard and PS/2 Mouse PortsJLAN1/2 Enable/Disable Jumper SettingsExplanation Jumpers Cmos ClearPower Force On VGA Enable/DisableSMBus to PCI Slots Watch DogAlarm Reset Onboard IndicatorsJlan LEDs System Status LEDOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Deﬁnitions IDE1, IDE2 IDE ConnectorsPrecautions Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools RequiredChassis Front View Control PanelAccessing the Drive Bays Drive Bay Installation/RemovalSystem Fans System Fan FailureMounting a Serial ATA drive in a drive carrier Serial ATA Drive InstallationInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationReplacing the Power Supply Power SupplyPower Supply Failure Page Introduction How To Change the Conﬁguration DataChapter System Memory Main SetupProcessors Conﬁgure Advanced CPU Settings Advanced SettingsCPU Conﬁguration Sub-Menu System Time/System DateIDE Conﬁguration Sub-Menu Combined Mode OperationIDE Conﬁguration ATA Ports DeﬁnitionType LBA/Large ModeBlock Multi-Sector Transfer A.R.T. For Hard disk drivesPCI/PnP Conﬁguration Floppy ConﬁgurationPalette Snooping Allocate IRQ to PCI VGAPCI IDE BusMaster Offboard PCI/ISA IDE CardSuper IO Conﬁguration Sub-Menu Advanced Chipset Settings Apci Conﬁguration Power ConﬁgurationPCI/PCI Error Logging Watch Dog TimerPCI/PCI Express Error Logging Event Log ConﬁgurationPCI Express Conﬁguration Remote Access ConﬁgurationMPS Conﬁguration Serial Port Mode Remote AccessRedirection After Bios Post Sredir Memory Display DelaySystem Health Monitor USB ConﬁgurationSystem Fan Monitor Boot SettingsFan Speed Control Modes Fan1 Speed to Fan6 SpeedsBios Settings Conﬁguration Hard Disk Drives Boot Device PriorityRemovable Drives CD/DVD DrivesChange Supervisor Password Security SettingsChange User Password Clear User PasswordExit Options Load Optimal DefaultsSaving Changes and Exit Discarding Changes and ExitLoad Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Intel 6300ESB I/O Controller Hub Appendix C Software InstallationSerial ATA Sata Adaptec RAID Conﬁguration Utility ARC Conﬁguring Sata RAIDAdaptec Sata HostRAID Controller Driver Using the Array Conﬁguration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array To initialize drives Deleting a Bootable ArrayInitializing Disk Drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Conﬁguration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Speciﬁcations Power Supply WeightSystem Cooling System Input Requirements