SUPER MICRO Computer 6014L-T Server Chassis Features, System Power, Serial ATA Subsystem

Page 15

Chapter 1: Introduction

1-3 Server Chassis Features

The following is a general outline of the main features of the SC811LT-260 chas- sis.

System Power

When confi gured as a SuperServer 6014L-T, the SC811LT-260 chassis includes a single 260W power supply.

Serial ATA Subsystem

For the 6014L-T, the SC811LT-260 chassis was designed to support two Serial ATA hard drives, which are hot-swappable units.

Note: The operating system you use must have RAID support to enable the hot- swap capability of the Serial ATA drives.

Control Panel

The SC811LT-260's control panel provides important system monitoring and control information. LEDs indicate power on, network activity, hard disk drive activity and system overheat conditions. The control panel also includes a main power button and a system reset button.

Rear I/O Panel

The SC811LT-260 is a 1U rackmount chassis. Its I/O panel provides one PCI ex- pansion slot, one COM port (another is internal), two USB ports, PS/2 mouse and keyboard ports, a VGA port and two Gb Ethernet ports. (See Figure 1-2.)

1-5

Image 15
Contents Super Manual Revision Release Date March 6 Preface About This ManualManual Organization Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Serverboard Setup System SafetySMB Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesIntel E7520 Chipset System Block Diagram Control Panel Server Chassis FeaturesSystem Power Serial ATA SubsystemRear I/O Panel Cooling SystemAsia-Pacific Contacting SupermicroHeadquarters EuropePage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LED Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsUnpacking Chapter Advanced Serverboard SetupPrecautions Handling the ServerboardServerboard Installation Installing the Heatsink BracketsInstalling the Serverboard Installing the Processors Processor and Heatsink InstallationInstalling the Heatsinks Installed processorInstalled heatsink Removing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables I/O Ports Connecting the Control PanelInstalling Memory Dimm Installation See FigureMemory Support PCI card installation Adding PCI CardsPCI slots Super X6DLP-EG2 Layout Serverboard DetailsX6DLP-EG2 Quick Reference Jumper Description Default SettingConnector Description Onboard Indicators DescriptionPower LED Connector DefinitionsATX Power Connector Processor Power ConnectorPower Fail LED NIC1/2 LEDsOverheat/Fan Fail LED Chassis Intrusion Reset ButtonPower Button JLAN1/2 Ethernet PortsUniversal Serial Bus USB0/1 Universal Serial Bus HeadersFan Headers Speaker/Power LED/Keylock Wake-On-RingWake-On-LAN ATX PS/2 Keyboard and PS/2 Mouse Ports ConnectorPower Fault SMB Power I2 CCmos Clear Jumper SettingsJLAN1/2 Enable/Disable Explanation JumpersWatch Dog VGA Enable/DisablePower Force On SMBus to PCI SlotsSystem Status LED Onboard IndicatorsAlarm Reset Jlan LEDsOnboard LED Indicators DS7, DS8 Onboard LED Indicators DS1, DS5Parallel Printer Port Header Parallel Port, Floppy, IDE and Sata Drive ConnectionsSata Connectors Floppy ConnectorIDE Drive Connectors Pin Definitions IDE1, IDE2 IDE ConnectorsTools Required Chapter Advanced Chassis SetupPrecautions Static-Sensitive DevicesChassis Front View Control PanelSystem Fan Failure Drive Bay Installation/RemovalAccessing the Drive Bays System FansMounting a Serial ATA drive in a drive carrier Serial ATA Drive InstallationInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationPower Supply Power Supply FailureReplacing the Power Supply Page How To Change the Configuration Data ChapterIntroduction Main Setup ProcessorsSystem Memory System Time/System Date Advanced SettingsConfigure Advanced CPU Settings CPU Configuration Sub-MenuATA Ports Definition Combined Mode OperationIDE Configuration Sub-Menu IDE ConfigurationA.R.T. For Hard disk drives LBA/Large ModeType Block Multi-Sector TransferPCI/PnP Configuration Floppy ConfigurationOffboard PCI/ISA IDE Card Allocate IRQ to PCI VGAPalette Snooping PCI IDE BusMasterSuper IO Configuration Sub-Menu Advanced Chipset Settings Apci Configuration Power ConfigurationEvent Log Configuration Watch Dog TimerPCI/PCI Error Logging PCI/PCI Express Error LoggingRemote Access Configuration MPS ConfigurationPCI Express Configuration Sredir Memory Display Delay Remote AccessSerial Port Mode Redirection After Bios PostSystem Health Monitor USB ConfigurationFan1 Speed to Fan6 Speeds Boot SettingsSystem Fan Monitor Fan Speed Control ModesBios Settings Configuration CD/DVD Drives Boot Device PriorityHard Disk Drives Removable DrivesClear User Password Security SettingsChange Supervisor Password Change User PasswordDiscarding Changes and Exit Load Optimal DefaultsExit Options Saving Changes and ExitLoad Fail-Safe Defaults Appendix a Bios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description DS7/DS8 LED Post Codes LED IndicatorsUncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C Software Installation Serial ATA SataIntel 6300ESB I/O Controller Hub Configuring Sata RAID Adaptec Sata HostRAID Controller DriverAdaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACU Viewing Array Properties Managing ArraysCreating Arrays Deleting ArraysPage Assigning Array Properties RAID Levels Adding a Bootable Array Deleting a Bootable Array Initializing Disk DrivesTo initialize drives Page Page To rebuild an array Rebuilding ArraysTo access the disk utilities Using the Disk UtilitiesYou can choose from the following options Exiting the Adaptec RAID Configuration UtilityInstalling the ICH5R/6300 ESBDriver Installing Additional Drivers Installing Other Software Programs and DriversSupero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Specifications System Input Requirements WeightPower Supply System Cooling