SPX Cooling Technologies manual CS4000 Mini Controller with Ethernet Dimensions

Page 47

CS4000 Mini Controller with Ethernet

NOTE: All dimensions are in inches with millimeters in square brackets.

Figure 4-1. CS4000 Mini Controller with Ethernet Dimensions

To mount the controller you require four 1/4-20-in bolts or screws.

Page 4-2

T-38324-A

39-30-38324

Page 46 Page 48
Image 47
Page 46 Page 48
Contents
Technical Reference Manual CS4000 Mini Controller with EthernetHour Technical Support Toll Free Please Note Limited Warranty Acknowledgments Who Should Use This Manual How to Use This ManualPreface Conventions Ieee AbbreviationsThis page is left blank intentionally Contents Mounting the CS4000 Mini Controller with Ethernet Index-1 Figures Tables This page is left blank intentionally Receiving, Sending and Storing Data OverviewUsing Ethernet Network Hub Using a 485 Network using Sdlc LAN Using an Interbus-S Digital I/O Module Using the RS-232 Serial PortDeciding How to Set Up the Controller Using the Siemens 3964R Barcode ProtocolThis page is left blank intentionally Think Safety First Wear Approved Safety Glasses AT ALL Times General Machine SafetyElectrical Safety CS4000 Mini Controller with Ethernet Identifying the Components LED Display Front PanelInterbus-S I/O Connector Parameter Set SwitchAccess Screws AC Power CordTool Connector ConnectorSdlc I/O Network Connector RS-422 ConnectorEthernet Connector Printer/Barcode ConnectorFuses Enclosure InteriorIdentifying the Components Front View of the TCM 38324-A 39-30-38324 Tool Control ModuleTach Gain Speed Trim Device Control Module Servo AmplifierCS4000 Mini Controller with Ethernet Backplane BackplaneBackplane Fuses Address SwitchesBoard Power Supply10shows the Ethernet interface card and its sub-components Ethernet Interface CardDescription of Ethernet Interface Card LEDs OUT Interbus-S Module2describes the LEDs Fuses Ground Fault Circuit InterrupterMounting the CS4000 Mini Controller with Ethernet Installing the CS4000 Mini Controller with EthernetCS4000 Mini Controller with Ethernet Dimensions Power/Connection Requirements Power and Connection-RequirementsGrounding Meeting the AC Input Power RequirementsBlack wire external WiringRed wire internal Defaults Remote Input Circuit Schematics Installing the CS4000 Mini Controller with Ethernet CS4000 Mini Controller with Ethernet Connector Connector Pinout DefinitionsTool Connector Printer/Barcode Connector RS-422 ConnectorTool Control Module TCM Network Connector RS-232 ConnectorInterbus-S OUT Connector This page is left blank intentionally Programming the Ethernet Interface Card Setting Up the EthernetProcedure 5-1. Programming the Ethernet Interface Card Setting Up the Ethernet Click OK Establishing a Successful Connection via COM1 Flash the application file to the Ethernet interface card Error Message Displayed when the Attempted Connection Fails 38324-A 39-30-38324 May 38324-A Procedure 5-2. Editing Application Information Updating Application SettingsSelect the Ip Address tab Select the Comm Options tab Setting Up Visual Supervisor for an Ethernet Network Editing VSMain.ini for an Ethernet Network Open VSMain.ini using Notepad Procedure 5-3. Editing VSMain.ini for an Ethernet NetworkEthernet RJ-45 Modular Jack Pinout Using Ethernet Network CablesProcedure 5-4. Testing the Network From a Laptop Computer Testing the Ethernet NetworkCS4000 Mini Controller with Ethernet 18. Select Communications Port May 38324-A Specify the communications port settings. See Figure Login to the attached Ethernet interface card Tini 21. Opening the Command Prompt Window May 38324-A Procedure 5-5. Testing the Network From a Host ComputerTesting Ethernet Network Cables Setting Up Visual Supervisor for a 485 Network Setting Up the 485 NetworkInstalling the Sdlc Card Editing VSMain.ini for a 485 Network VSMain.ini configured for a 485 Network 38324-A 39-30-38324Communications Detachable=0 #Ports=1 CommOcx1=SDLC Procedure 6-1. Editing VSMain.ini for a 485 NetworkAssigning a Network Address Switch Binary NumberAddress 5, 6, 7 Procedure 6-2. Setting the Address for the Controller Using 485 Network Cables This page is left blank intentionally Using RS-232 Cables Setting Up the RS-232 LinkSetting Up Visual Supervisor This page is left blank intentionally Replacement Parts Maintenance/TroubleshootingReplacing Backplane Fuses Replacing Main Power FusesCleaning the Enclosure Window Ethernet Network TroubleshootingApplication Program Interface API RS-422 Siemens 3964R InterfaceTechnical Information Assembly DrawingThis page is left blank intentionally Technical Information This page is left blank intentionally Technical Information This page is left blank intentionally Index Index-2 38324-A 39-30-38324 Part Number
Top Page Image Contents