NetComm NP2500 manual Contact Information, Copyright Information, Customer Information

Page 43

APPENDIX C Registration and Warranty Information

All NetComm Limited (“NetComm”) products have a standard 12 month warranty from date of purchase against defects in manufacturing and that the products will operate in accordance with the specifications outlined in the User Guide. However some products have an extended warranty option (please refer to your packaging). To be eligible for the extended warranty you must supply the requested warranty information to NetComm within 30 days of the original purchase by registering on-line via the NetComm web site at:

www.netcomm.com.au

Contact Information

If you have any technical difficulties with your product, please do not hesitate to contact NetComm’s Customer Support Department.

Email:support@netcomm.com.au

Fax:

(+612) 9424-2010

Web:www.netcomm.com.au

Copyright Information

This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or review, as permitted under the Copyright Act, no part may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical, recording or otherwise, without the prior written permission of NetComm Limited. NetComm Limited accepts no liability or responsibility, for consequences arising from the use of this product. Please note that the images used in this document may vary slightly from those of the actual product. Specifications are accurate at the time of the preparation of this document but are subject to change without notice.

NetComm Limited reserves the right to change the specifications and operating details of this product without notice. NetComm is a registered trademark of NetComm Limited. All other trademarks are acknowledged the property of their respective owners.

Customer Information

ACA (Australian Communications Authority) requires you to be aware of the following information and warnings:

(1)This unit shall be connected to the Telecommunication Network through a line cord which meets the requirements of the ACA TS008 Standard.

(2)This equipment has been tested and found to comply with the Standards for C-Tick and or A-Tick as set by the ACA. These standards are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio noise and, if not installed and used in accordance with the instructions detailed within this manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur with the installation of this product in your home or office. If this equipment does cause some degree of interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, we encourage the user to try to correct the interference by one or more of the following measures:

Change the direction or relocate the receiving antenna.

Increase the separation between this equipment and the receiver.

NP2500 24-Port 10/100 PoE + 2-Port 10/100/1000 WebSMART Switch User Guide

43

YML842 Rev1

 

Image 43
Contents Page Contents RJ-45 Network Ports Purpose About this GuideTerms/Usage Fast Ethernet Technology IntroductionGigabit Ethernet Technology Power over Ethernet PoE Switching TechnologyVlan Virtual Local Area Network Features Installation Unpacking and InstallationUnpacking Installing the Switch on a Rack Installing the Switch on a DesktopMount the Switch in the rack Connecting Network Cable Connecting Network CableAC Power Front Panel Identifying External ComponentsRear Panel Rear panel of the SwitchSystem LEDs Understanding LED IndicatorsFast Ethernet PoE Port Status LEDs Port 1 ~ Gigabit Ethernet Port Status LEDs Installing the Web Management Utility ConfigurationWeb Management Utility Discovery ListView Trap Monitor ListDelete Item Device SettingConfiguration Setting Add ItemFirmware Upgrade Password ChangeWeb Access Login Configuring the SwitchSetup menu Setup MenuPort Settings Configuring Setup SettingSetup menu QoS Auto, and Disable-for speed or port disable selectionsFlow Control ManagementVlan Group Settings Vlan Settings Virtual Local Area NetworkTrunk Settings Trunk SettingSniffer port Mirror SettingRX receive mode Forward it to the sniffer portPOE Port Status PoE SettingSelected port Current Select to enable or disable the PoE functionPower limit POE System SettingSystem Status Device StatusStatistic StatisticServer System SettingAbnormal* Transmit Error Trap SettingAddress of the manager where the trap is to be sent From where the IP to be loginBackup Setting Set PasswordFunction to change the password Logout Reset SettingGeneral Power over EthernetVcci Warning PerformanceFCC Warning CE Mark WarningYML842 Rev1 Straight and crossover cable configuration RJ-45 Network PortsCross-Over Cabling Straight-Through CablingCopyright Information Contact InformationCustomer Information Product Warranty YML842 Rev1