NetComm NP2500 manual Product Warranty

Page 44

receiver/TV is connected.

Consult an experienced radio/TV technician for help.

(3)The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply with any other product or do not use any other power supply that is not approved for use with this product by NetComm. Failure to do so may cause damage to this product, fire or result in personal injury.

Product Warranty

The warranty is granted on the following conditions:

1.This warranty extends to the original purchaser (you) and is not transferable;

2.This warranty shall not apply to software programs, batteries, power supplies, cables or other accessories supplied in or with the product;

3.The customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable requirements of NetComm including producing such evidence of purchase as NetComm may require;

4.The cost of transporting product to and from NetComm’s nominated premises is your responsibility; and,

5.NetComm does not have any liability or responsibility under this warranty where any cost, loss, injury or damage of any kind, whether direct, indirect, consequential, incidental or otherwise arises out of events beyond NetComm’s reasonable control. This includes but is not limited to: acts of God, war, riot, embargoes, acts of civil or military authorities, fire, floods, electricity outages, lightning, power surges, or shortages of materials or labour.

6.The customer is responsible for the security of their computer and network at all times. Security features may be disabled within the factory default settings. NetComm recommends that you enable these features to enhance your security.

The warranty is automatically voided if:

1.You, or someone else, use the product, or attempts to use it, other than as specified by NetComm;

2.The fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power supply or communication line, whether caused by thunderstorm activity or any other cause(s);

3.The fault is the result of accidental damage or damage in transit, including but not limited to liquid spillage;

4.Your product has been used for any purposes other than that for which it is sold, or in any way other than in strict accordance with the user manual supplied;

5.Your product has been repaired or modified or attempted to be repaired or modified, other than by a quali- fied person at a service centre authorised by NetComm; and,

6.The serial number has been defaced or altered in any way or if the serial number plate has been removed.

Limitations of Warranty

The Trade Practices Act 1974 and corresponding State and Territory Fair Trading Acts or legalisation of another Government (“the relevant acts”) in certain circumstances imply mandatory conditions and warranties which cannot be excluded. This warranty is in addition to and not in replacement for such conditions and warranties.

To the extent permitted by the Relevant Acts, in relation to your product and any other materials provided with the product (“the Goods”) the liability of NetComm under the Relevant Acts is limited at the option of NetComm to:

Replacement of the Goods; or

Repair of the Goods; or

Payment of the cost of replacing the Goods; or

Payment of the cost of having the Goods repaired.

44

NP2500 24-Port 10/100 PoE + 2-Port 10/100/1000 WebSMART Switch User Guide

 

YML842 Rev1

Image 44
Contents Page Contents RJ-45 Network Ports Terms/Usage About this GuidePurpose Gigabit Ethernet Technology IntroductionFast Ethernet Technology Vlan Virtual Local Area Network Switching TechnologyPower over Ethernet PoE Features Unpacking Unpacking and InstallationInstallation Installing the Switch on a Desktop Installing the Switch on a RackMount the Switch in the rack Connecting Network Cable Connecting Network CableAC Power Identifying External Components Front PanelRear panel of the Switch Rear PanelFast Ethernet PoE Port Status LEDs Port 1 ~ Understanding LED IndicatorsSystem LEDs Gigabit Ethernet Port Status LEDs Configuration Installing the Web Management UtilityDiscovery List Web Management UtilityMonitor List View TrapDevice Setting Configuration SettingAdd Item Delete ItemPassword Change Firmware UpgradeWeb Access Configuring the Switch LoginSetup Menu Setup menuSetup menu Configuring Setup SettingPort Settings Auto, and Disable-for speed or port disable selections Flow ControlManagement QoSVlan Settings Virtual Local Area Network Vlan Group SettingsTrunk Setting Trunk SettingsMirror Setting RX receive modeForward it to the sniffer port Sniffer portSelected port PoE SettingPOE Port Status Select to enable or disable the PoE function Power limitPOE System Setting CurrentDevice Status System StatusStatistic StatisticSystem Setting ServerTrap Setting Address of the manager where the trap is to be sentFrom where the IP to be login Abnormal* Transmit ErrorFunction to change the password Set PasswordBackup Setting Reset Setting LogoutPower over Ethernet GeneralPerformance FCC WarningCE Mark Warning Vcci WarningYML842 Rev1 RJ-45 Network Ports Straight and crossover cable configurationStraight-Through Cabling Cross-Over CablingCustomer Information Contact InformationCopyright Information Product Warranty YML842 Rev1