Net Optics Director Front Panel, Monitor Port LEDs, DNM / Network Port LEDs, Gigabit Port LEDs

Page 13

Director

Director Front Panel

The features of the Director front panel are shown in the following diagram.

10 SFP			2 XFP			DNM with 10/100/1000			DNM with SX Fiber
Monitor			Configurable			Copper Network Ports			Network Ports
Ports			10GbE Ports			(6 In-line or 12 Span Ports)			(6 In-line or 12 Span Ports)

Director ™

1

2

3

4

5

2

1

6 7 8 9 10

A B

A

B

In-Line 10/100/1000

10	LINK	In-Line	A		B		A		B		A		B
100	ACT	GigaBit
1000		GigaBit
			1	2	3	4	5	6	7	8	9	10	11	12

www.netoptics.com

Power LEDs	Monitor Ports		2 Director Network Module (DNM) Slots

Network Ports

Figure 6: Director Front Panel

Monitor Port LEDs

Each Monitor port has two light-emitting diode (LED) indicators. The Link LED is illuminated when a link is estab- lished. The Activity LED blinks when traffic is passing through the port. They are located in the middle between the two rows of SFPs.

DNM / Network Port LEDs

Each 10/100/1000 Network or Span port has two LEDs. The Link LED is illuminated when a link is established. The Activity LED blinks when traffic is passing through the port. The Link LED also indicates the link speed: amber for 10Mbps, yellow for 100Mbps, and green for a 1000Mbps (1 Gbps). They are integrated in the RJ-45 connectors, Link on the left and Activity on the right.

Each 1-Gigabit Fiber Network or Span port has a single LED. It illuminates solid when a link is established, and it flashes when traffic is passing through the port. These Link LEDs are located below the LC fiber connectors.

10 Gigabit Port LEDs

Each configurable 10-Gigabit port has a single LED. It illuminates solid when a link is established, and it flashes when traffic is passing through the port. These Link LEDs are located to the left of the XFP fiber connectors.

Power LEDs

Two LED indicators for power, one for each of the redundant power supplies.

9

Image 13

Contents Data Monitoring Switch Trademarks and Copyrights Contents Chapter Chapter Configuring Filters Using the CLIAppendix a Appendix BChapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure TechnologyDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDirector Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorBaud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management portTo log into the CLI Log into the CLIChange Director Password Configure Director using the CLITo change the login password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port ModesSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsEnvironmental Specifications, DNMCertifications Available ModelsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved