Net Optics Director manual Command Sub-Command Arguments Example and description, Commit

Page 48

Director

Command

Sub-Command

Arguments

Example and description

 

 

 

 

!

 

[#] (a number)

!3

 

 

 

Executes a command from the CLI command history

 

 

 

buffer

 

 

 

(see history command)

 

 

 

 

commit

 

 

commit

 

 

 

Activates pending changes previously defined using

 

 

 

filter commands AND saves the changes as the new

 

 

 

default configuration

 

 

 

 

date

 

<date>

date 06/24/2008

 

 

 

Arguments:

 

 

 

<date> is mm/dd/yyyy

 

 

 

Sets the system calendar date; if <date> is omitted,

 

 

 

the current date is displayed

 

 

 

 

del

 

<filename>

del my_configuration-1

 

 

 

Arguments:

 

 

 

<filename> is the name of the file to delete; a

 

 

 

string; do not include an extension

 

 

 

Deletes a previously saved Director configuration file

 

 

 

(see save command)

 

 

 

 

exit

 

 

exit

 

 

 

Exits the CLI shell (same as logout and quit)

 

 

 

Note: To maintain system security, control is not

 

 

 

returned to the command shell.

 

 

 

 

filter

add

ipv6=y

filter add in_ports=n1.1-n1.3 ip_src=10.1.1.1

 

 

in_ports=<network_portlist>

action=drop

 

 

<qual>=<value>

Arguments:

 

 

action=< redir drop >

ipv6=y for IPv6 addressing; omit for IPv4

 

 

redir_ports=<monitor_portlist>

<network_portlist> — traffic from the network

 

 

 

ports specified in this portlist is aggregated before

 

 

Notes:

being sent to the filter

 

 

The command may include

<qual> and <value> are filter qualifiers and values

 

 

as listed in the table that follows this table; any

 

 

any number of <qual>, up

 

 

number of <qual>=<value> pairs may be included

 

 

to the limit of Director's filter

 

 

Specify redir or drop as the filter action —

 

 

resources (approximately

 

 

if redir, packets matching all of the <qual> are

 

 

1,000 <qual> per chassis)

 

 

copied to all of the Monitor ports specified in the

 

 

The action=< redir drop >

 

 

portlist <monitor_portlist>

 

 

argument is required

 

 

if drop, packets matching all of the <qual> are

 

 

 

 

 

If action=redir, then

dropped

 

 

redir_ports=<monitor_portlist>

Defines a filter, including the network and monitor

 

 

argument is required

ports involved in the filter; filter is pending (inactive)

 

 

 

until activated by a filter commit or commit command

 

 

 

Note: If the filter command does not include any

 

 

 

<qual>, it defines aggregation, regeneration, and

 

 

 

matrix switching functions without filtering

 

 

 

 

 

clear

 

filter clear

 

 

 

Clears all active filters

 

 

 

 

44

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Data Monitoring Switch Trademarks and Copyrights Contents Chapter Configuring Filters Using the CLI ChapterAppendix a Appendix BChapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools 10 Gigabit in-line network connection using a network Tap In-line Monitoring of 10 Gigabit LinksPower LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceInstall Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect Power to Director Connect the local CLI InterfaceConnect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management portLog into the CLI To log into the CLIConfigure Director using the CLI Change Director PasswordTo change the login password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Show name show running, factory, default, or file nameConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkConfigure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsXFP Port Protocol = Monitor Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersFilter running command Enter filter list to view the pending filter list Filter capacity Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10Daisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisSpecifications, DNM EnvironmentalCertifications Available ModelsAppendix B Command Line Interface Command Sub-Command Arguments Example and description CommitFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Director Filter Parameters Qual Value Example Description Vlan=128Appendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved
Top Page Image Contents