Net Optics manual Set the Current Date and Time, Save and Load Director Configurations

Page 23

Director

Set the Current Date and Time

Director maintains a time-of-day clock which is used to record the time of traffic peak utilization events. Time is based on the 24-hour clock. The clock must be initialized using the CLI or another management tool.

To change the current date and time:

1.Enter time hh:mm:ss where hh is hour, mm is minutes, and ss is seconds.

2.Enter date mm/dd/yyyy where mm is month, dd is day of the month, and yyyy is year.

Example: time 12:20:00 date 06/24/2008

Save and Load Director Configurations

The entire configuration of Director, including port configurations and filters, can be saved to and loaded from files stored on Director's internal disk drive. When working with these files from within the CLI, specify only a filename (up to 32 characters long) without an extension. The current configuration is automatically kept in a file named defaultcfg. This file is automatically loaded at power up or when the system is reset, so your configuration is persistent. However, you may wish to save copies of various configurations that you use for different purposes. For example, each person that uses the device can maintain a separate configuration.

To save the Director configuration:

• Enter save <filename> where <filename> is the name for this configuration. The configuration is saved.

To load a Director configuration:

• Enter load <filename> where <filename> is the name of a saved configuration. The configuration is loaded.

To view a list of all saved Director configurations:

• Enter list. A list of Director configurations is displayed.

To view a saved Director configuration:

• Enter show <filename> where <filename> is the name of a saved configuration. The configuration is displayed.

19

Image 23

Contents Data Monitoring Switch Trademarks and Copyrights Contents Appendix B Chapter Configuring Filters Using the CLIChapter Appendix aChapter Introduction Passive, Secure Technology Key FeaturesEase of Use Monitor port FilteringDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDNM / Network Port LEDs Power LEDsDirector Front Panel Monitor Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationRack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect the local CLI Interface Connect Power to DirectorTo connect the CLI for remote use over the Management port Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control TipTo log into the CLI Log into the CLITo change the login password Configure Director using the CLIChange Director Password Change Port Modes To change the port modeAssign a New Manager IP Address To assign a new Manager IP address to DirectorSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksConnect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsAvailable Models Specifications, DNMEnvironmental CertificationsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved