Net Optics Director Chapter Configuring Filters Using the CLI, Appendix a, Appendix B, Appendix C

Page 4

Director

Chapter 3

Configuring Filters Using the CLI

Syntax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Copy Traffic From Any Network Port to Any Monitor Port. . . . . . . . . . . . . . . . . . . . 26 Aggregate Traffic From Any Set of Network Ports to Any Monitor Port. . . . . . . . . . . . . . . 26 Regenerate Traffic to Any Set of Monitor Ports. . . . . . . . . . . . . . . . . . . . . . . . . 27 Create Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Create Complex Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 View filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Work with configurable 10 Gigabit ports. . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Understand filter interactions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Understand pending and active filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Chapter 4
Daisy-chaining Multiple Director Chassis	40
Appendix A
Director Specifications	41
Appendix B
Command Line Interface	43
Filter parameters	. . . . . . . . . . . . . . . . . . . 49
Appendix C
Protocol Numbers	51
Limitations on Warranty and Liability	54

Image 4

Contents Data Monitoring Switch Trademarks and Copyrights Contents Chapter Configuring Filters Using the CLI ChapterAppendix a Appendix BChapter Introduction Key Features Ease of UseMonitor port Filtering Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools 10 Gigabit in-line network connection using a network Tap In-line Monitoring of 10 Gigabit LinksPower LEDs Director Front PanelMonitor Port LEDs DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect Power to Director Connect the local CLI InterfaceConnect the remote CLI Interface Baud Data bits No parity 1 stop bit No flow controlTip To connect the CLI for remote use over the Management portLog into the CLI To log into the CLIChange Director Password Configure Director using the CLITo change the login password To change the port mode Assign a New Manager IP AddressTo assign a new Manager IP address to Director Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Show name show running, factory, default, or file nameConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsXFP Port Protocol = Monitor Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersFilter running command Enter filter list to view the pending filter list Filter capacity Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10Daisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisSpecifications, DNM EnvironmentalCertifications Available ModelsAppendix B Command Line Interface Command Sub-Command Arguments Example and description CommitFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Director Filter Parameters Qual Value Example Description Vlan=128Appendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved