Net Optics Director manual Appendix C Protocol Numbers, Num Keyword Protocol

Page 55

Director

Appendix C

Protocol Numbers

The official Assigned Internet Protocol Numbers list is maintained by the Internet Assigned Numbers Authority and can be found at http://www.iana.org/assignments/protocol-numbers. The list as of April 18, 2008 is reproduced in the following table (without references).

Num	Keyword	Protocol

0	HOPOPT	IPv6 Hop-by-Hop Option

1	ICMP	Internet Control Message

2	IGMP	Internet Group Management

3	GGP	Gateway-to-Gateway

4	IP	IP in IP (encapsulation)

5	ST	Stream

6	TCP	Transmission Control

7	CBT	CBT

8	EGP	Exterior Gateway Protocol

9	IGP	any private interior gateway
		(used by Cisco for their
		IGRP)

10	BBN-	BBN RCC Monitoring
	RCC-
	MON

11	NVP-II	Network Voice Protocol

12	PUP	PUP

13	ARGUS	ARGUS

14	EMCON	EMCON

15	XNET	Cross Net Debugger

16	CHAOS	Chaos

17	UDP	User Datagram

18	MUX	Multiplexing

19	DCN-	DCN Measurement Subsys-
	MEAS	tems

20	HMP	Host Monitoring

21	PRM	Packet Radio Measurement

22	XNS-IDP	XEROX NS IDP

23	TRUNK-1	Trunk-1

24	TRUNK-2	Trunk-2

25	LEAF-1	Leaf-1

26	LEAF-2	Leaf-2

27	RDP	Reliable Data Protocol

28	IRTP	Internet Reliable Transaction

29	ISO-TP4	ISO Transport Protocol Class 4

Num	Keyword	Protocol

30	NETBLT	Bulk Data Transfer Protocol

31	MFE-NSP	MFE Network Services
		Protocol

32	MERIT-	MERIT Internodal Protocol
	INP

33	DCCP	Datagram Congestion Control
		Protocol

34	3PC	Third Party Connect Protocol

35	IDPR	Inter-Domain Policy Routing
		Protocol

36	XTP	XTP

37	DDP	Datagram Delivery Protocol

38	IDPR-	IDPR Control Message
	CMTP	Transport Proto

39	TP++	TP++ Transport Protocol

40	IL	IL Transport Protocol

41	IPv6	Ipv6

42	SDRP	Source Demand Routing
		Protocol

43	IPv6-	Routing Header for IPv6
	Route

44	IPv6-Frag	Fragment Header for IPv6

45	IDRP	Inter-Domain Routing Pro-
		tocol

46	RSVP	Reservation Protocol

47	GRE	General Routing Encapsula-
		tion

48	DSR	Dynamic Source Routing
		Protocol

49	BNA	BNA

50	ESP	Encap Security Payload

51	AH	Authentication Header

52	I-NLSP	Integrated Net Layer Security
		TUBA

53	SWIPE	IP with Encryption

54	NARP	NBMA Address Resolution
		Protocol

51

Image 55

Contents Data Monitoring Switch Trademarks and Copyrights Contents Appendix B Chapter Configuring Filters Using the CLIChapter Appendix aChapter Introduction Passive, Secure Technology Key FeaturesEase of Use Monitor port FilteringDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDNM / Network Port LEDs Power LEDsDirector Front Panel Monitor Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorTo connect the CLI for remote use over the Management port Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control TipTo log into the CLI Log into the CLIChange Director Password Configure Director using the CLITo change the login password Change Port Modes To change the port modeAssign a New Manager IP Address To assign a new Manager IP address to DirectorSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsAvailable Models Specifications, DNMEnvironmental CertificationsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved