Net Optics Director manual L2TP

Page 57

Director

Num	Keyword	Protocol

115	L2TP	Layer Two Tunneling Protocol

116	DDX	D-II Data Exchange (DDX)

117	IATP	Interactive Agent Transfer
		Protocol

118	STP	Schedule Transfer Protocol

119	SRP	SpectraLink Radio Protocol

120	UTI	UTI

121	SMP	Simple Message Protocol

122	SM	SM

123	PTP	Performance Transparency
		Protocol

124	ISIS over
	IPv4

125	FIRE

110	CRTP	Combat Radio Transport
		Protocol

127	CRUDP	Combat Radio User Data-
		gram

128	SSCOP-
	MCE

129	IPLT

130	SPS	Secure Packet Shield

131	PIPE	Private IP Encapsulation
		within IP

132	SCTP	Stream Control Transmission
		Protocol

133	FC	Fibre Channel

Num	Keyword	Protocol

134	RSVP-
	E2E-
	IGNORE

135	Mobility
	Header

136	UDPLite

137	MPLS-
	in-IP

138	manet	MANET Protocols

139	HIP	Host Identity Protocol

140		Unassigned
to		Use for experimentation and
252		testing

253

254		Use for experimentation and
		testing

255	Reserved

53

Image 57

Contents Data Monitoring Switch Trademarks and Copyrights Contents Chapter Chapter Configuring Filters Using the CLIAppendix a Appendix BChapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure TechnologyDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDirector Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorBaud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management portTo log into the CLI Log into the CLIConfigure Director using the CLI Change Director PasswordTo change the login password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port ModesSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksConfigure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsEnvironmental Specifications, DNMCertifications Available ModelsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved