Net Optics Director manual Image

Page 50

Director

Command	Sub-Command	Arguments	Example and description

image		< 1 2 >	image 2
			Arguments:
			Valid values are 1 and 2
			Chooses which system image to boot from (see
			upgrade command)

	show		image show
			Lists the names of both system images and indicates
			which one is running, and which one is selected to
			boot from (arrow next to image name)

list			list
			Shows a list of filenames of saved Director device
			configurations (see save command)

load		<filename>	load my_configuration-1
			Arguments:
			<filename> is the name of the file to load; a string;
			do not include an extension
			Loads a previously saved Director configuration (see
			save command)

logout			logout
			Exits the CLI shell (same as exit and quit)
			Note: To maintain system security, control is not
			returned to the command shell.

module	show		module show
			Lists information about Director hardware modules
			including system serial number, DNM types, and
			XFPs

passwd			passwd
			Interactively changes the password of the SSH user
This			account
command
is only
available
at root
level

ping		<address>	ping 10.1.1.4
			Arguments:
			<address> is an IP address
			Pings the specified IP address to check for connectivity

port	set	ports=<portlist>	port set n1.1-n1.3 autoneg=on duplex=full
		autoneg=< on off >	Arguments:
		duplex=< full half >	<portllist> is a portlist
		speed=< 10 100 1000 >	For other arguments, select a value from the
			listed choices
			For 10/100/100 Copper interface Network and Moni-
			tor ports, enables or disables autonegotiation; selects
			the duplex mode; and sets the fixed speed (10Mbps,
			100Mbps, or 1000Mbps) if autonegotiation is off

	show		port show
			Displays the current port status and settings

46

Image 50

Contents Data Monitoring Switch Trademarks and Copyrights Contents Appendix a Chapter Configuring Filters Using the CLIChapter Appendix BChapter Introduction Monitor port Filtering Key FeaturesEase of Use Passive, Secure TechnologyAbout this Guide DescriptionDirector Architecture Director internal architectureUSB port Director ManagementTypical Application Network LinksMonitoring Tools 10 Gigabit in-line network connection using a network Tap In-line Monitoring of 10 Gigabit LinksMonitor Port LEDs Power LEDsDirector Front Panel DNM / Network Port LEDsDirector Rear Panel XFPChapter Installing Director Plan the Installation Unpack and Inspect the Director deviceRack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect Power to Director Connect the local CLI InterfaceTip Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control To connect the CLI for remote use over the Management portLog into the CLI To log into the CLITo change the login password Configure Director using the CLIChange Director Password To assign a new Manager IP address to Director To change the port modeAssign a New Manager IP Address Change Port ModesSave and Load Director Configurations Set the Current Date and TimeUsing the CLI Help Command To view CLI help informationUsing the CLI Command History Buffer Show name show running, factory, default, or file nameConnect Span Ports to Director To connect a Span portConnect Director With In-line Network Links To connect an in-line network linkConnect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Chapter Configuring Filters Using the CLI SyntaxEnter filter commit. The switch connection is activated Copy Traffic From Any Network Port to Any Monitor PortRegenerate Traffic to Any Set of Monitor Ports Lter add inports=n1.1 action=redir redirports=m.3-m.5Create Filters To create a filter that selects IPv4 packets by protocolCreate Complex Filters Logical and filter connectionView filters UDPWork with configurable 10 Gigabit ports Configurable 10 Gigabit XFP ports used as Network portsXFP Port Protocol = Monitor Port Understand filter interactions CAMFlow diagram now looks as follows Exclusive filters N1.1 ipproto=UDP action=drop N1.1 m.1To change the Director filter configuration Understand pending and active filtersFilter running command Enter filter list to view the pending filter list Filter capacity Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10Daisy-chaining Multiple Director Chassis Appendix a Director Specifications Specifications, chassisCertifications Specifications, DNMEnvironmental Available ModelsAppendix B Command Line Interface Command Sub-Command Arguments Example and description CommitFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Director Filter Parameters Qual Value Example Description Vlan=128Appendix C Protocol Numbers Num Keyword ProtocolMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved