Net Optics manual Configure Director using the CLI, Change Director Password

Page 21

Director

Configure Director using the CLI

You should be logged into the Director CLI. The factory-set default values for Director are:

•Username: admin

•Password: netoptics

•IP Address: 10.60.4.180 (address for remote CLI, and for Indigo manager software, when available)

•Netmask: 255.0.0.0 (associated with IP Address)

•Manager IP Address: 192.168.1.2 (address for SNMP traps)

•Gateway IP Address: 10.0.0.1 (associated with Manager IP Address)

•All ports enablesd

A complete list of CLI commands can be viewed by typing Help at the CLI prompt. It is also provided in Appendix B. You will now use the CLI to:

•Change the login password

•Assign a new IP Address, Netmask, and Gateway IP Addresses

•Assign new remote manager IP Address

•Change port modes

•Set the date and time

•Save and load Director configurations

•Try out the CLI Help command

Your CLI screen should be displaying the "Net Optics:" prompt as shown here:

Net Optics>

If you do not see the "Net Optics>" prompt, try typing Help followed by the Enter key. If the prompt is still not dis- played, repeat the instructions in the preceding section Connect the local CLI Interface or Connect the remote CLI Interface and log in again.

Change Director Password

It is strongly recommended that you change the login password from the default to provide security against unauthorized access.

To change the login password:

1.Enter user mod name=admin pw=<new password> priv=1. The password is changed.

2.Record the new password in a secure location.

If you wish to change the user name, use the user add command to create a new user account under that name. You can use the user del command to delete the admin account if you wish.

17

Image 21

Contents Data Monitoring Switch Trademarks and Copyrights Contents Chapter Chapter Configuring Filters Using the CLIAppendix a Appendix BChapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure TechnologyDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDirector Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall Director Network Modules Install SFP and XFP Monitor port ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorBaud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management portTo log into the CLI Log into the CLIConfigure Director using the CLI Change Director PasswordTo change the login password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port ModesSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksConfigure a Matrix Switch connection in Director Check the InstallationConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsEnvironmental Specifications, DNMCertifications Available ModelsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved