Net Optics Director manual About this Guide, Description

Page 7

Director

About this Guide

Please read this entire guide before installing Director. This guide applies to the following part numbers:

Chassis Part Number	Description

DIR-3400	Director Main Chassis with 10 SFP monitor ports
DIR-7400	Director Main Chassis with 10 SFP monitor ports, 2 XFP 10GbE ports, 2 XFP uplink ports
DNM Part Number	Description

DNM-100	6-Port 10/100/1000 Copper In-Line Module
DNM-110	12-Port 10/100/1000 Copper Span Module
DNM-200	6-Port Gigabit SX Fiber 62.5μm In-Line Module
DNM-210	12-Port Gigabit SX Fiber 62.5μm Span Module
DNM-220	6-Port Gigabit SX Fiber 50μm In-Line Module
DNM-230	12-Port Gigabit SX Fiber 50μm Span Module
DNM-300	6-Port Gigabit LX Fiber In-Line Module
DNM-310	12-Port Gigabit LX Fiber Span Module
DNM-320	6-Port Gigabit ZX Fiber In-Line Module
DNM-330	12-Port Gigabit ZX Fiber Span Module

3

Image 7

Contents Data Monitoring Switch Trademarks and Copyrights Contents Appendix B Chapter Configuring Filters Using the CLIChapter Appendix aChapter Introduction Passive, Secure Technology Key FeaturesEase of Use Monitor port FilteringDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDNM / Network Port LEDs Power LEDsDirector Front Panel Monitor Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationInstall SFP and XFP Monitor port Modules Install Director Network ModulesRack Mount the Director device Connect the local CLI Interface Connect Power to DirectorTo connect the CLI for remote use over the Management port Connect the remote CLI InterfaceBaud Data bits No parity 1 stop bit No flow control TipTo log into the CLI Log into the CLIChange Director Password Configure Director using the CLITo change the login password Change Port Modes To change the port modeAssign a New Manager IP Address To assign a new Manager IP address to DirectorSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksCheck the Installation Configure a Matrix Switch connection in DirectorConnect Monitoring Tools to Director Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsAvailable Models Specifications, DNMEnvironmental CertificationsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved