Net Optics manual Install Director Network Modules, Install SFP and XFP Monitor port Modules

Page 17

Director

Install Director Network Modules

If the Director Network Modules (DNMs) are not already installed when you receive the unit, install them by sliding them into the DNM slots in the front panel. (If there is a plate covering the DNM slot, remove it by unscrewing two thumb‑screws, and then install the DNM module.) The DNM circuit boards ride in the rails provided in the slots. Push in the DNM firmly until you feel the connectors mate and the bezel is flush with the front panel, but do not force them. If you encounter resistance, withdraw the module and try again, making sure to align the circuit board in the rails and slide the module straight in. When the DNM is fully seated, fasten it to the front panel with the two captured thumbscrews.

If you are only using a single DNM, it should be installed in the left slot (Slot 1).

A B

2	A
1	B
1

www.netoptics.com

Slot 1

Slot 2

Figure 8: Installing Director Network Modules

Install SFP and XFP Monitor port Modules

SFP and XFP modules are shipped separately. Install them as desired in the SFP and XFP slots in the front on the chassis, and the two XFP slots in the rear. For each module, remove the temporary plug from the SFP or XFP slot and insert the module until it clicks into place. The photograph on the cover of this Guide shows properly installed SFP and XFP modules.

Rack Mount the Director device

Director is designed for rack mounting in a 19-inch rack panel. The panel occupies one rack unit. To rack mount the Director device, simply slide it into the desired rack location and secure it using the four supplied screws.

13

Image 17

Contents Data Monitoring Switch Trademarks and Copyrights Contents Chapter Chapter Configuring Filters Using the CLIAppendix a Appendix BChapter Introduction Ease of Use Key FeaturesMonitor port Filtering Passive, Secure TechnologyDescription About this GuideDirector internal architecture Director ArchitectureDirector Management USB portNetwork Links Typical ApplicationMonitoring Tools In-line Monitoring of 10 Gigabit Links 10 Gigabit in-line network connection using a network TapDirector Front Panel Power LEDsMonitor Port LEDs DNM / Network Port LEDsXFP Director Rear PanelChapter Installing Director Unpack and Inspect the Director device Plan the InstallationRack Mount the Director device Install Director Network ModulesInstall SFP and XFP Monitor port Modules Connect the local CLI Interface Connect Power to DirectorBaud Data bits No parity 1 stop bit No flow control Connect the remote CLI InterfaceTip To connect the CLI for remote use over the Management portTo log into the CLI Log into the CLITo change the login password Configure Director using the CLIChange Director Password Assign a New Manager IP Address To change the port modeTo assign a new Manager IP address to Director Change Port ModesSet the Current Date and Time Save and Load Director ConfigurationsTo view CLI help information Using the CLI Help CommandShow name show running, factory, default, or file name Using the CLI Command History BufferTo connect a Span port Connect Span Ports to DirectorTo connect an in-line network link Connect Director With In-line Network LinksConnect Monitoring Tools to Director Configure a Matrix Switch connection in DirectorCheck the Installation Syntax Chapter Configuring Filters Using the CLICopy Traffic From Any Network Port to Any Monitor Port Enter filter commit. The switch connection is activatedLter add inports=n1.1 action=redir redirports=m.3-m.5 Regenerate Traffic to Any Set of Monitor PortsTo create a filter that selects IPv4 packets by protocol Create FiltersLogical and filter connection Create Complex FiltersUDP View filtersConfigurable 10 Gigabit XFP ports used as Network ports Work with configurable 10 Gigabit portsXFP Port Protocol = Monitor Port CAM Understand filter interactionsFlow diagram now looks as follows N1.1 ipproto=UDP action=drop N1.1 m.1 Exclusive filtersUnderstand pending and active filters To change the Director filter configurationFilter running command Enter filter list to view the pending filter list Inports=n1.1-n1.7 Ipproto=6 Vlan=100 Redirports=m.1-m.5,m.10 Filter capacityDaisy-chaining Multiple Director Chassis Specifications, chassis Appendix a Director SpecificationsEnvironmental Specifications, DNMCertifications Available ModelsAppendix B Command Line Interface Commit Command Sub-Command Arguments Example and descriptionFilter discard Image Quit User add name=bob pw=bob-pw priv=3 Filter parameters Vlan=128 Director Filter Parameters Qual Value Example DescriptionNum Keyword Protocol Appendix C Protocol NumbersMobile L2TP Limitations on Warranty and Liability By Net Optics, Inc. All Rights Reserved