Intelligent Motion Systems MForce Series Microstepping PowerDrive operating instructions

Page 66

Prototype Development Cable PD02-2300-FL3

IMS recommends the Prototype Development Cable PD02-3400-FL3 for interfacing power to the MForce PowerDrive.

10 ft (3.0 m)

Power Supply Return (Ground)

Pin 1 (Red Wire)

Drain Wire (Connect to Earth at Power Supply)

Motor Power (+12 to +75 VDC)

Figure A.12: PD02-3400-FL3

Prototype Development Cable PD04-MF34-FL3

The PD04-MF34FL3 is a 10’ (3.0 M) Prototype Development Cable used to connect the MForce PowerDrive to a stepping motor:

Pair Number	Color Combination	Interface Signal			MForce Wire Crimp
(Cable/Pair)					Connection Pin Number
1/1	Black		Phase A		1
1/1	White				2
	White		Phase A		2
1/2	Black	Phase B			3

	White				4
	White		Phase B		4

Table A.2: PD04-MF34-FL3

Drain Wire

Pin 4

Pin 3

Pin 2

Pin 1

Drain Wire

General Specifications

Length: 10 Feet (3.0 Meters)

Conductor: 16 AWG

Twisted Pairs

Shield: 100% Flexfoil

Jacket: PVC

Figure A.13: PD04-MF34-FL3

A-8	Microstepping MForce PowerDrive Manual Revision R040507

Image 66

Contents Forcetm Microstepping MForce PowerDrive Product Manual Table Of Contents Appendices List of Figures List of Tables Microstepping MForce PowerDrive MForce PowerDrive FrontStepping Motor Connecting the Motor Connect Opto Reference and Logic InputsForcetm Intentionally Left Blank Introduction to the Microstepping MForce PowerDrive ConfiguringFeatures and Benefits Microstepping MForce PowerDrive Detailed Specifications General SpecificationsSetup Parameters Mechanical Specifications Dimensions in Inches mmPin Assignment and Description Pin # Function DescriptionP3 Connector DC Power, 2-Pin Locking Wire Crimp P4 Connector MotorOptions and Accessories Parameter Setup Cable and AdaptersPrototype Development Cable Intentionally Left Blank Forcetm Microstepping MForce PowerDrive Manual Revision R040507 Mounting and Connection Guidelines Mounting RecommendationsSecuring Power Leads and Logic Leads Mounting Hole PatternLayout and Interface Guidelines Power P3 Logic and SPI Communications P1Motor P4 Intentionally Left Blank Interfacing DC Power Choosing a Power Supply for Your MForce PowerDriveRecommended IMS Power Supplies DC Power Supply RecommendationsISP300-7 Unregulated Switching Supply IP804 Unregulated Linear SupplyBasic DC Power Connection Recommended Power and Cable ConfigurationsExample a DC Power Cabling Under 50 Feet Transformer 10 to 28 VAC RMS for 48 VDC Systems Winding Inductance Motor Selection and InterfaceSelecting a Motor Types and Construction of Stepping MotorsLead Stepping Motor Parallel Configuration Recommended IMS MotorsFrame Enhanced 6.0A Frame Enhanced 2.4A Not Available with Double ShaftFrame Enhanced 3.0A Frame Enhanced 6.3APhase Connector Pin Lead MotorsPhase a Motor Connections MForce PowerDrive Phase OutputsRecommended Motor Cabling Example a Motor Cabling Less Than 50 FeetExample B Motor Cabling Greater Than 50 Feet Recommended Motor Cable AWG SizesMicrostepping MForce PowerDrive Manual Revision R040507 Enable Input Isolated Logic Input Pins and ConnectionsIsolated Logic Input Characteristics Logic Interface and ConnectionQuadrature Step ClockDirection Up/DownSTEP/DIRECTION Timing Optocoupler Reference Optocoupler ReferenceNPN Open Collector Interface Sinking Input Connection ExamplesSwitch Interface Sinking Switch Interface ExampleMinimum Required Connections +V +12 to +48Connecting SPI Communications SPI Pins and Connections Logic Level Shifting and Conditioning CircuitSPI Master with Multiple Microstepping MForce PowerDrive 4 SPI Master with a Single Microstepping MForce PowerDriveUsing the IMS SPI Motor Interface Installation Configuration Parameters and RangesColor Coded Parameter Values IMS SPI Motor Interface Menu Options FileView Upgrade RecallHelp Msel Microstep Resolution Select Msel Microstep Resolution SelectionSet Connected/Disconnected IndicatorFactory ExitInput Clock Type Screen 2 I/O Settings Configuration ScreenEnable Active High/Low Input Clock FilterFault Indication IMS Part Number/Serial Number ScreenIMS SPI Upgrader Screen Upgrade InstructionsInitialization Screen Port MenuUsing User-Defined SPI SPI Timing NotesCheck Sum Calculation for SPI SPI Commands and Parameters MSBWrite SPI Communications SequenceAppendices Intentionally Left Blank MD-CC300-000 USB to SPI Parameter Setup Cable Optional Prototype Development CablesAdapter Cables Installation Procedure for the MD-CC300-000 Installing the Cable/VCP DriversFigure A.5 Hardware Update Wizard Screen Determining the Virtual COM Port VCP PD12-1434-FL3 Power, I/O and SPI Wire Color CodePrototype Development Cable PD02-2300-FL3 Prototype Development Cable PD04-MF34-FL3Warranty Excellence in Motion