GarrettCom manual Removing PM Cards, Magnum 700X Mini-Concentrator

Page 30

PM Card

PM Cards

Magnum 700X

Magnum 700X Mini-Concentrator

Magnum 700X Mini-Concentrators	Installation and User Guide (05/98)

Slowly and firmly push the PM into position. Once inserted, secure the PM card using the two screws on the front panel of the unit. Once all PM cards needed have been installed (including face plates for empty slots), replace the chassis cover.

NOTE: All PM slots need not be filled in order for the unit to be operational. When leaving PM slots empty, always use a face plate (Magnum PM-FP) to cover the opening in the front panel to keep the unit clean, and for safety.

3.5Removing PM Cards

To properly remove a PM card from the Magnum 700X Mini-Concentrator, follow the steps below.

1.Removing 700X Chassis Cover and PM Retaining Screws

Follow the procedure described for Face Plates in Section 3.3, Steps 1 and 2, above.

2.Removing PM Card

Gently pull the PM card up and out of the connector socket. If the slot from which the PM card has been removed is to remain open be sure to install an PM face plate. If another PM card is replacing the one that

has been removed, follow the steps as described for installing an PM

card discussed on the preceding pages.

NOTE: Use a face plate (Magnum PM-FP) to cover the opening in the front panel if you are leaving any 700X Mini-Concentrator slots empty.

Magnum 700X

Magnum 700X Mini-Concentrator

GARRETT

25

Image 30

Contents Magnum 700X Mini-Concentrator Magnum Mini-Concentrator Installation and User Guide TrademarksPhone 510 Contacting Garrett CommunicationsTable of Contents IntroductionMagnum  Specifications Warranty Technical Specifications, ConnectorsLED Indicators on Chassis PackagingSpecifications Repeater Port Modules RPMs Specifications Bridge Port Modules BPMsOrdering Information Magnum 700X Mini-Concentrator Introduction Inspecting the Package and ProductProduct Description Magnum 700X Chassis 1 Magnum 700X Mini-ConcentratorMagnum 700X Repeater Port Modules RPMs RPM-DTE, RPM-FST, RPM-FSC, RPM-TP, & PM-FPRPM-BNC Magnum RPM-BNC RPM-AUI2 AUI Pin Assignments Pin FunctionRPM-FST Fiber ST, Twist-lock Connector RPM-DTEMagnum RPM-FST Jumper Across Distances Supported RPM-FSC Fiber SC, Snap-in ConnectorConnector Magnum RPM-FSC RPM-SMF Single-mode Fiber 3 kmNot used 10 kmMagnum RPM-TP Proper cooling air flow, and for safety Magnum PM-FPRPM-TP Twisted Pair PM-FPPage BPM-AUI BPM-FSTMagnum BPM-FST Module is designed with internal Wiring STP of 150m 500 ft.. ThisBPM-TP Transceiver functionality. The LinkRPMs Repeater Port Modules for All Standard Ethernet Media Front Mounted Connectors and LEDsInternal Universal Power Supply with Auto-ranging Optional Bridge Port Modules BPMsApplications Ieee Standard Reference Max. Distance Taps PM TypeMedia Ieee Standard Connector PM type InstallationConnecting Ethernet Media Locating Magnum 700X Mini-ConcentratorsConnecting ThinNet 10BASE2 BNC Connecting ThickNet 10BASE5 AUIConnecting Drop Cable 10BASE5 DTE Connecting Fiber Optic SC-type, Snap-in Connecting Single-Mode Fiber Optic SMFConnecting Twisted Pair RJ-45, Unshielded or Shielded Removing the PM Face PlatePower Supply Connector socket slot Installing PM CardsInstalling the PM Card Align the connector Pins on the PM cardRemoving PM Cards Operation Repeater FunctionalityBPM Local Bridge Functionality 2c and 4.2d respectively. When an Cases where an internal packet is filteredWhen the packet’s source is external, it Written there. This happens when a2d External Packet Filtered Powering the Magnum 700X Mini-Concentrator 12.2e Local Isolation with Bridge Port ModuleChassis LEDs Magnum 700X chassis unit LEDsPM LEDs Troubleshooting Before Calling for AssistanceWhen Calling for Assistance Return Material Authorization RMA ProcedureNo Problem Found Shipping and Packaging InformationAppendix a Warranty Information