GarrettCom 6K32 manual Connecting Fiber Optic ST-type, twist-lock, Copper

Page 27

Magnum 6K32 Managed Switch

Installation and User Guide (02/05)

individually selected and configured per-port. See Section 2.4 for a description of the PMs.

The various media types supported along with the corresponding IEEE

802.3 and 802.3u standards and connector types are as follows:

IEEE Standard

Media Type

Max. Distance

Port Module

Fiber:

mm1 Fiber

 

 

 

1000BASE-FX

220m ( ft) GBIC-SXSC

 

sgl.m2 Fiber

70km

GBIC-LXSC

100BASE-FX

mm1 Fiber

2.0km

(6,562 ft)

6K6-MSC, -MST

 

sgl.m2 Fiber

18.0km (95K ft)

SSC, SSCL

small form factor

mm1 Fiber

2.0km

(6,562 ft)

6K8-MTRJ, -MLC

small form factor

sgl.m1 Fiber

15 km

 

6KP8- SLC

Copper:

 

 

10BASE-T and 100BASE-TX twisted pair

100m (328 ft)

6K8-RJ45

1 mm = multi-mode

2 sgl.m = single-mode

3.2.1Connecting Fiber Optic ST-type, “twist-lock”

The following procedure applies to installations using a PM with ST-type fiber connectors. This procedure applies to ports using a 6K32 module, MST-type port.

1.Before connecting the fiber optic cable, remove the protective dust caps from the tips of the connectors on the PM. Save these dust caps for future use.

2.Wipe clean the ends of the dual connectors with a soft cloth or lint-free lens tissue dampened in alcohol. Make certain the connectors are clean before connecting.

Note: One strand of the duplex fiber optic cable is coded using color bands at regular intervals; you must use the color-coded strand on the associated ports at each end of the fiber optic segment.

3.Connect the Transmit (TX) port (light colored post) on the Magnum PM to the Receive (RX) port of the remote device. Begin with the color-coded strand of the cable for this first TX-to-RX connection.

4.Connect the Receive (RX) port (dark colored post on the PM) to the Transmit

(TX) port of the remote device. Use the non-color coded fiber strand for this.

5.The LINK LED on the front of the PM will illuminate when a proper connection has been established at both ends (and when power is ON in the unit). If LINK is not lit after cable connection, the normal cause is improper cable polarity. Swap the fiber cables at the PM connector to remedy this situation.

3.2.2Connecting Fiber Optic SC-type, "Snap-In"

The following procedure applies to installations using a PM with SC-type fiber

connectors, i.e., using 6K-MSC, 6K-SSC single-mode.

When connecting fiber media to SC connectors, simply snap on the two square male connectors into the SC female jacks of the 6KPM until it clicks and secures.

www . GarrettCom . com

21

Image 27
Contents Corporate Headquarters GarrettCom, IncTrademarks Table of Contents Contacting GarrettCom, IncCanadian Emission Introduction Troubleshooting Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications DC Power Supply Options Fiber connector types supportedManagement Console connector Power Supply InternalAlarm Contact Optional Manual switches for modular slot port module onlyAgency Approvals Ordering Information Gigabit Transceiver options 6KP8-45-2MT 6KP8-45-2SLC LC connectorsIntroduction Inspecting the Package and Product Product Description Magnum 6K32 Managed Switch Magnum 6K32 and 6K32R chassis Mode for best fiber distance Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber100Mb fiber eight Port modules for the Magnum Eight-Port Copper Module, 6K8-RJ45 @ RJ-45 + 2@ 100Mb SC@ RJ-45 + 2@ 100Mb ST Four-Port 10 Mb mm Fiber ST Modules Packet Prioritization, 802.1p QOS Gigabit 1000Mbps port modulesFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K32 Features and Benefits „ Managed switching for high performance Ethernet LANs„ Features Fiber-Built-In Applications Example 1 Magnum 6K32 Switch for a Vlan applicationInternet Internet Example 3 Redundant ApplicationSwitch #1 Installation Locating Magnum 6K32 SwitchesConnecting Ethernet Media Copper Connecting Fiber Optic ST-type, twist-lockConnecting Fiber Optic SC-type, Snap-In Ieee Standard Media Type Max. Distance Port Module FiberMedia Ieee Standard Connecting Single-Mode Fiber OpticTable-Top or Shelf Mounting Rack-mounting for 19 Retma racks, regular Magnum 6K32sMagnum 6K32 unit. These 1 Mountings for Magnum 6K32 units rack-mounted in a frame Rack-mounting, Reverse version of the Magnum 6K32s2 Reverse Magnum 6K32 units, rack- mounted in a frame Powering the Magnum 6K32 Managed SwitchPreparation for Installing and Removing 6KPMs 6K32 Port Module 6KPM Installation1a Removing front panel after the screws being removed Remove Chassis Cover1b Pulling out the top coved from the chassis base 1d Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K32Securely latching up 6KPM Cards into a Magnum 6K32 Removing 6KPM Cards 2g Top View 6KPM Module installed inside a 6K32 SwitchRemoving a 6KPM Card Console DB-9 Port Connecting the Console Terminal to Magnum 6K32 ManagementPin Signal Description DB-9 Console port connectorFiltering and Forwarding Switching FunctionalityACT Status LEDsAuto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports PWRWww . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4Magnum 6K32 Managed Switch Port Modules 6KPM Module Description 1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Flstfx is a combo fiber Connectors and configuredAs 10Mb Half-duplex by Default for 10Mb fiber Magnum 6KP4Provides an advantage Through combining copper Mode SC-type connectors. ItEquipped with 4 dual speed Copper ports and 2 SingleWww . GarrettCom . com Port@ 100Mbps Multi-Mode Fiber port Activity FULL/HALFLink Placing more ports on one module Magnum 6KP8-45MTModule is a combo module with Copper and fiber Small Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port 10a 6KP8-45-2LC, 6@ 10/100Mbps RJ-45 and 2@100Mb single-mode FX , LC Small-Form-Factor GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector 12 6KM-BLNK@ 1000Mb Fiber SC + 2@ 100Mb SC Before Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information Appendix B Internal DC Power Supply OptionsB1.0 Specifications for Magnum 6K32 SWITCHES, DC Power Power Supply Internal -48VDC OptionB3.0 Applications for DC Powered Switches Power Supply Internal 125 VDC Option Industrial ApplicationsB4.0 Installation B4.1 UL Requirements for DC-powered unitsB5.0 Operation B6.0 Ordering Information B7.0 TroubleshootingGND Appendix C Internal DC Dual-Source Power OptionC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignExample Magnum 6K32R-24VDC or Magnum 6K32R-125VDC C5.1 UL RequirementsC6.0 Ordering Information Example Magnum 6K32R-48VDC