GarrettCom manual Removing 6KPM Cards, 2g Top View 6KPM Module installed inside a 6K32 Switch

Page 37

Magnum 6K32 Managed Switch

Installation and User Guide (02/05)

NOTE:. When leaving 6KPM slots empty, always use a face plate (Magnum 6K8- BLNK) to cover the slot opening in the front panel. This will maintain proper cooling air flow, safety, and operation as required by FCC, CE, and other regulations.

Step 6. Now screw down the daughter board with 7 #440 screws except the last two at the end, so that it holds the daughter board securely. The figure below shows the top view of 6KPM card after successfully installing the 6KPM cards inside the

Magnum 6K32.

Fig. 3.5.2g Top View : 6KPM Module installed inside a 6K32 Switch

Step 7. Once the installation of granddaughter and daughter modules is done properly, the front panel screen plates(come along with the 6K-module) need to be properly placed on the front of the chassis cover to complete the installation process.

Step 8. Once the 6KPM cards have been installed, the chassis top cover should be replaced by matching at the two front corners properly and slide in until it reaches the rear end and fit properly to match the holes. Make sure the chassis cover is aligned properly before securing the enclosure. Place the front panel part at the end by sliding in to the front side and secure it with 12 screws as being mentioned earlier.

NOTE (Reverse mount Model): The Reverse model require a LED Decal, (for checking the speed, F/H, and activity status)

3.5.3Removing 6KPM Cards

To properly remove a 6KPM card from the 6K32 Managed Switch, follow the 3 steps below.

Step 1. Remove chassis cover See procedures in Section 3.5.1 above.

Caution: Be sure the power cord is unplugged.

www . GarrettCom . com

31

Image 37

Contents Corporate Headquarters GarrettCom, IncTrademarks Contacting GarrettCom, Inc Table of ContentsCanadian Emission Introduction Troubleshooting Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications Management Console connector Fiber connector types supportedPower Supply Internal DC Power Supply OptionsManual switches for modular slot port module only Alarm Contact OptionalAgency Approvals Ordering Information Gigabit Transceiver options 6KP8-45-2MT 6KP8-45-2SLC LC connectorsIntroduction Inspecting the Package and Product Product Description Magnum 6K32 Managed Switch Magnum 6K32 and 6K32R chassis Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Mode for best fiber distance100Mb fiber eight Port modules for the Magnum @ RJ-45 + 2@ 100Mb SC Eight-Port Copper Module, 6K8-RJ45@ RJ-45 + 2@ 100Mb ST Four-Port 10 Mb mm Fiber ST Modules Packet Prioritization, 802.1p QOS Gigabit 1000Mbps port modulesFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K32 „ Managed switching for high performance Ethernet LANs Features and Benefits„ Features Fiber-Built-In Applications Example 1 Magnum 6K32 Switch for a Vlan applicationInternet Internet Example 3 Redundant ApplicationSwitch #1 Locating Magnum 6K32 Switches InstallationConnecting Ethernet Media Connecting Fiber Optic SC-type, Snap-In Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperMedia Ieee Standard Connecting Single-Mode Fiber OpticRack-mounting for 19 Retma racks, regular Magnum 6K32s Table-Top or Shelf MountingMagnum 6K32 unit. These 1 Mountings for Magnum 6K32 units rack-mounted in a frame Rack-mounting, Reverse version of the Magnum 6K32s2 Reverse Magnum 6K32 units, rack- mounted in a frame Powering the Magnum 6K32 Managed SwitchPreparation for Installing and Removing 6KPMs 6K32 Port Module 6KPM Installation1a Removing front panel after the screws being removed Remove Chassis Cover1b Pulling out the top coved from the chassis base 1d Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K32Securely latching up 6KPM Cards into a Magnum 6K32 Removing 6KPM Cards 2g Top View 6KPM Module installed inside a 6K32 SwitchRemoving a 6KPM Card Pin Signal Description Connecting the Console Terminal to Magnum 6K32 ManagementDB-9 Console port connector Console DB-9 PortFiltering and Forwarding Switching FunctionalityAuto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports Status LEDsPWR ACTWww . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4Magnum 6K32 Managed Switch Port Modules 6KPM Module Description 1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module As 10Mb Half-duplex by Default for 10Mb fiber Connectors and configuredMagnum 6KP4 Flstfx is a combo fiberEquipped with 4 dual speed Mode SC-type connectors. ItCopper ports and 2 Single Provides an advantage Through combining copperWww . GarrettCom . com Activity FULL/HALF Port@ 100Mbps Multi-Mode Fiber portLink Module is a combo module with Magnum 6KP8-45MTCopper and fiber Small Form Factor Placing more ports on one module9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port 10a 6KP8-45-2LC, 6@ 10/100Mbps RJ-45 and 2@100Mb single-mode FX , LC Small-Form-Factor GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector12 6KM-BLNK 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC + 2@ 100Mb SC Before Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureB1.0 Specifications for Magnum 6K32 SWITCHES, DC Power Appendix B Internal DC Power Supply OptionsPower Supply Internal -48VDC Option Shipping and Packaging InformationB3.0 Applications for DC Powered Switches Power Supply Internal 125 VDC Option Industrial ApplicationsB4.1 UL Requirements for DC-powered units B4.0 InstallationB5.0 Operation B6.0 Ordering Information B7.0 TroubleshootingGND Appendix C Internal DC Dual-Source Power OptionC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC6.0 Ordering Information C5.1 UL RequirementsExample Magnum 6K32R-48VDC Example Magnum 6K32R-24VDC or Magnum 6K32R-125VDC