GarrettCom manual Table-Top or Shelf Mounting, Magnum 6K32 unit. These

Page 29

Magnum 6K32 Managed Switch	Installation and User Guide (02/05)
Media	IEEE Standard	Connector
Twisted Pair (CAT 5E)	1000BASE-T	RJ-45

NOTE : It is recommended that high quality CAT. 5E cables (which work for both 100 Mb and 1000Mb) be used whenever possible in order to provide flexibility in a mixed-speed network.

The following procedure describes how to connect a 1000BASE-T twisted pair segment to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted pair cables.

1.1000Base-T connections require that all four pairs or wires be connected. Insert either end of the cable with an RJ-45 plug into the RJ-45 connector of the port. Note that, even though the connector is shielded, either unshielded or shielded cables and wiring may be used.

2.Connect the other end of the cable to the corresponding device

3.Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established

3.3Table-Top or Shelf Mounting

The Magnum 6K32 Manageable Switches can be easily mounted on a table-top

or any suitable horizontal surface, and has four rubber feet to provide stability without scratching finished surfaces.

3.3.1Rack-mounting (for 19” RETMA racks), regular Magnum 6K32s

Installation of a Magnum 6K32 Fiber Switch in a 19” rack is a simple

procedure. The units are 1U (1.70”) high. When properly installed, the front-mounted LED status indicators should be in plain view and easy to read.

Rack-mount installation requires

special 19” rack-mounted brackets

and screws (included with each

PW

10/100

1

3

5

10/100

1

3

5 LK

Magnum

10/100

1

3

LK

LK

Magnum 6K32 unit). These

Managed

AC

F/

AC

F/

AC

Switch

F/

2

4

6

2

4

6

2

4

6

10/100

LK

10/100

LK

10/100

LK

F/H

F/H

AC

F/H

AC

AC

brackets attach to the front sides

of the Switch (regular package,

i.e., not the Reverse version),

which is then typically fastened into a standard 19” RETMA rack as shown here.

The 23” brackets and the ETSI (European metric, approx. 21”) brackets are also available (optional) for rack-mounting of Magnum 6K32 Switches. These brackets are popular in the Telco industry where they are a standard for Central Office rack- mounting purposes. The 23” and the ETSI brackets are mainly used for larger equipment

www . GarrettCom . com

23

Image 29

Contents Corporate Headquarters GarrettCom, IncTrademarks Canadian Emission Table of ContentsContacting GarrettCom, Inc Introduction Troubleshooting Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications Management Console connector Fiber connector types supportedPower Supply Internal DC Power Supply OptionsAgency Approvals Alarm Contact OptionalManual switches for modular slot port module only Ordering Information Gigabit Transceiver options 6KP8-45-2MT 6KP8-45-2SLC LC connectorsIntroduction Inspecting the Package and Product Product Description Magnum 6K32 Managed Switch Magnum 6K32 and 6K32R chassis 100Mb fiber eight Port modules for the Magnum Mode for best fiber distanceEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber @ RJ-45 + 2@ 100Mb ST Eight-Port Copper Module, 6K8-RJ45@ RJ-45 + 2@ 100Mb SC Four-Port 10 Mb mm Fiber ST Modules Packet Prioritization, 802.1p QOS Gigabit 1000Mbps port modulesFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K32 „ Features Fiber-Built-In Features and Benefits„ Managed switching for high performance Ethernet LANs Applications Example 1 Magnum 6K32 Switch for a Vlan applicationInternet Internet Example 3 Redundant ApplicationSwitch #1 Connecting Ethernet Media InstallationLocating Magnum 6K32 Switches Connecting Fiber Optic SC-type, Snap-In Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber CopperMedia Ieee Standard Connecting Single-Mode Fiber OpticMagnum 6K32 unit. These Table-Top or Shelf MountingRack-mounting for 19 Retma racks, regular Magnum 6K32s 1 Mountings for Magnum 6K32 units rack-mounted in a frame Rack-mounting, Reverse version of the Magnum 6K32s2 Reverse Magnum 6K32 units, rack- mounted in a frame Powering the Magnum 6K32 Managed SwitchPreparation for Installing and Removing 6KPMs 6K32 Port Module 6KPM Installation1a Removing front panel after the screws being removed Remove Chassis Cover1b Pulling out the top coved from the chassis base 1d Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K32Securely latching up 6KPM Cards into a Magnum 6K32 Removing 6KPM Cards 2g Top View 6KPM Module installed inside a 6K32 SwitchRemoving a 6KPM Card Pin Signal Description Connecting the Console Terminal to Magnum 6K32 ManagementDB-9 Console port connector Console DB-9 PortFiltering and Forwarding Switching FunctionalityAuto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports Status LEDsPWR ACTWww . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4Magnum 6K32 Managed Switch Port Modules 6KPM Module Description 1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module As 10Mb Half-duplex by Default for 10Mb fiber Connectors and configuredMagnum 6KP4 Flstfx is a combo fiberEquipped with 4 dual speed Mode SC-type connectors. ItCopper ports and 2 Single Provides an advantage Through combining copperWww . GarrettCom . com Link Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Module is a combo module with Magnum 6KP8-45MTCopper and fiber Small Form Factor Placing more ports on one module9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port 10a 6KP8-45-2LC, 6@ 10/100Mbps RJ-45 and 2@100Mb single-mode FX , LC Small-Form-Factor GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC + 2@ 100Mb SC 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector12 6KM-BLNK Before Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureB1.0 Specifications for Magnum 6K32 SWITCHES, DC Power Appendix B Internal DC Power Supply OptionsPower Supply Internal -48VDC Option Shipping and Packaging InformationB3.0 Applications for DC Powered Switches Power Supply Internal 125 VDC Option Industrial ApplicationsB5.0 Operation B4.0 InstallationB4.1 UL Requirements for DC-powered units B6.0 Ordering Information B7.0 TroubleshootingGND Appendix C Internal DC Dual-Source Power OptionC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC6.0 Ordering Information C5.1 UL RequirementsExample Magnum 6K32R-48VDC Example Magnum 6K32R-24VDC or Magnum 6K32R-125VDC