GarrettCom manual Installing 6KPM Cards in the Magnum 6K32

Page 35

Magnum 6K32 Managed Switch

Installation and User Guide (02/05)

(#256 flat head ) which hold the PM Face plate card slot securely. These six screws shown in the picture below are used to secure a PM face plate in position, but unscrew only four of the screws as shown in Fig. below. These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables. (See Figure 3.5.1d)

Figure 3.5.1d: Top View – 6KPM retaining screws hold Face Plate

3.5.2Installing 6KPM Cards in the Magnum 6K32

Up to four front-mounted 6KPM cards may be installed in one Magnum 6K32 Managed Switch unit. Follow these steps to install a 6KPM.

Step 1. Remove top chassis cover. See procedure in Section 3.5.1 above.

Step 2. Placed Granddaughter board (as shown in fig. 3.5.2a and 3.5.2b) on the chassis built in stand off (female) provided at the front of the 6K32 Main Board and screw down tightly with the three 5/16 stand-off (male) on the top of the Granddaughter board The 5/16 stand off has been used to place the daughter board on the top of the granddaughter board and latch it securely.

Fig 3.5.2b Granddaughter Board placed in modular slot and secured with three 7/16 stand-off’s as shown with arrow mark

www . GarrettCom . com

29

Image 35
Contents Corporate Headquarters GarrettCom, IncTrademarks Canadian Emission Table of ContentsContacting GarrettCom, Inc Introduction Troubleshooting Personal Hubs, 10Mb series Personal Switches, 10/100MbTechnical Specifications DC Power Supply Options Fiber connector types supportedManagement Console connector Power Supply InternalAgency Approvals Alarm Contact OptionalManual switches for modular slot port module only Ordering Information Gigabit Transceiver options 6KP8-45-2MT 6KP8-45-2SLC LC connectorsIntroduction Inspecting the Package and Product Product Description Magnum 6K32 Managed Switch Magnum 6K32 and 6K32R chassis 100Mb fiber eight Port modules for the Magnum Mode for best fiber distanceEight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber @ RJ-45 + 2@ 100Mb ST Eight-Port Copper Module, 6K8-RJ45@ RJ-45 + 2@ 100Mb SC Four-Port 10 Mb mm Fiber ST Modules Packet Prioritization, 802.1p QOS Gigabit 1000Mbps port modulesFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K32 „ Features Fiber-Built-In Features and Benefits„ Managed switching for high performance Ethernet LANs Applications Example 1 Magnum 6K32 Switch for a Vlan applicationInternet Internet Example 3 Redundant ApplicationSwitch #1 Connecting Ethernet Media InstallationLocating Magnum 6K32 Switches Copper Connecting Fiber Optic ST-type, twist-lockConnecting Fiber Optic SC-type, Snap-In Ieee Standard Media Type Max. Distance Port Module FiberMedia Ieee Standard Connecting Single-Mode Fiber OpticMagnum 6K32 unit. These Table-Top or Shelf MountingRack-mounting for 19 Retma racks, regular Magnum 6K32s 1 Mountings for Magnum 6K32 units rack-mounted in a frame Rack-mounting, Reverse version of the Magnum 6K32s2 Reverse Magnum 6K32 units, rack- mounted in a frame Powering the Magnum 6K32 Managed SwitchPreparation for Installing and Removing 6KPMs 6K32 Port Module 6KPM Installation1a Removing front panel after the screws being removed Remove Chassis Cover1b Pulling out the top coved from the chassis base 1d Top View 6KPM retaining screws hold Face Plate Installing 6KPM Cards in the Magnum 6K32Securely latching up 6KPM Cards into a Magnum 6K32 Removing 6KPM Cards 2g Top View 6KPM Module installed inside a 6K32 SwitchRemoving a 6KPM Card Console DB-9 Port Connecting the Console Terminal to Magnum 6K32 ManagementPin Signal Description DB-9 Console port connectorFiltering and Forwarding Switching FunctionalityACT Status LEDsAuto-Cross MDIXAuto-negotiation, for 10/100Mbps RJ-45 ports PWRWww . GarrettCom . com Flow-control, Ieee 802.3x standard ’cvr 6KP4Magnum 6K32 Managed Switch Port Modules 6KPM Module Description 1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Flstfx is a combo fiber Connectors and configuredAs 10Mb Half-duplex by Default for 10Mb fiber Magnum 6KP4Provides an advantage Through combining copper Mode SC-type connectors. ItEquipped with 4 dual speed Copper ports and 2 SingleWww . GarrettCom . com Link Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Placing more ports on one module Magnum 6KP8-45MTModule is a combo module with Copper and fiber Small Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port 10a 6KP8-45-2LC, 6@ 10/100Mbps RJ-45 and 2@100Mb single-mode FX , LC Small-Form-Factor GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector@ 1000Mb Fiber SC + 2@ 100Mb SC 11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector12 6KM-BLNK Before Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information Appendix B Internal DC Power Supply OptionsB1.0 Specifications for Magnum 6K32 SWITCHES, DC Power Power Supply Internal -48VDC OptionB3.0 Applications for DC Powered Switches Power Supply Internal 125 VDC Option Industrial ApplicationsB5.0 Operation B4.0 InstallationB4.1 UL Requirements for DC-powered units B6.0 Ordering Information B7.0 TroubleshootingGND Appendix C Internal DC Dual-Source Power OptionC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignExample Magnum 6K32R-24VDC or Magnum 6K32R-125VDC C5.1 UL RequirementsC6.0 Ordering Information Example Magnum 6K32R-48VDC