Enterasys Networks RBT-4102 manual Using the CLI to Upgrade Firmware

Page 80

Administration

Using the CLI to Upgrade Firmware

To download software from a TFTP/FTP Server, use the copy command from the Executive mode. The copy command requires you to specify either the file type and then the server type, or the server type and then the file type. You must then specify the file name, and IP address of the TFTP server. When the download is complete, you can use the dir command to check that the new file is present in the access point file system. To run the new software, use the reset board command to reboot the access point.

Example

RoamAbout 4102#

RoamAbout 4102#copy tftp file

1.Application image

2.Config file

3.Boot block image

Select the type of download<1,2,3>: [1]:1 TFTP Source file name:ets-img_v1017.bin TFTP Server IP:10.120.112.2

Firmware version of system is V1.0.16 and Updating Run-Time code v01.00.17 NOW! This firmware is compatible with hardware.

The software was properly copied over to the system and a reset is needed in order for the software changes to take place.

RoamAbout 4102#

4-44 Advanced Configuration

Image 80

Contents Enterasys RoamAbout Page Page Enterasys Networks, Inc. Firmware License Agreement Iii Page Enterasys Networks, Inc. Software License Agreement Page General Viii Contents Snmp Appendix a Default Settings Appendix B Troubleshooting IndexXii Purpose of This Manual Intended AudienceFirmware Version Support Associated DocumentsGetting Help Convention DescriptionIntroduction OverviewFeatures PolicyApplications Applications Introduction Network Configuration Ad Hoc Wireless LAN no Access Point or Bridge Network TopologiesInfrastructure Wireless LAN Infrastructure Wireless LANInfrastructure Wireless LAN for Roaming Wireless PCs Infrastructure Wireless LAN for RoamingInfrastructure Wireless Bridge Infrastructure Wireless BridgeNetwork Topologies Network Configuration Initial Setup Using the CLI Required ConnectionsLogging Enter no ip dhcp to disable Dhcp Using Web Management Initial Setup Using the CLI ```` Initial Setup Using the CLI Initial Setup Using the CLI Initial Setup Using the CLI Initial Setup Using the CLI Using the Web Interface Using the Command Line Interface CLISnmp Using Web Management to Configure System Information IdentificationUsing the CLI to Configure System Information EnabledDisabled SG SingaporeTCP / IP Settings Using Web Management to Configure TCP/IP TCP / IP Settings Using the CLI to Configure TCP/IP TCP/IP ConfigurationSSH Configuration Ethernet Settings ConfigurationTCP / IP Settings Radius Using Web Management to Configure Radius Radius Attributes Radius Accounting Attribute Description Using the CLI to Configure Radius Authentication Using Web Management to Configure Authentication Allowed Using the CLI to Configure AuthenticationLocal Using Web Management to Configure Filter Control and VLANs Filter Control and VLANsFilter Control and VLANs Using the CLI to Configure Filter Control and VLANs CLI Commands for Vlan SupportFilter Control and VLANs CLI Commands for Filtering SVP Commands CDP Settings Using Web Management to Configure CDPCDP Settings Using the CLI to Configure CDP Using Web Management to Configure Rogue AP Detection Rogue AP DetectionUsing the CLI to Configure Rogue AP Detection Ssid TT5Using Web Management to Configure Snmp SnmpSnmp Notifications Description Snmp Notifications Security Level Snmp Targets Using the CLI to Configure Snmp CLI Commands for SnmpCLI Commands for Configuring SNMPv3 Users and Groups TPSSnmp CLI Commands for Configuring SNMPv3 Targets CLI Commands for Configuring SNMPv3 Trap FiltersAdministration Changing the PasswordUsing Web Management to Change the Password Using the CLI to Change the Password Using Web Management to Enable and Disable Com PortUsing the CLI to Enable and Disable Com Port Enabling and Disabling Com PortUpgrading Firmware Using Web Management to Upgrade Firmware Using the CLI to Upgrade Firmware Using Web Management to Configure System Log System LogLogging Level Descriptions Error Level Using the CLI to Configure System Log Using Web Management to Configure Sntp Using the CLI to Configure Sntp TAIPEI, BeijingWDS and STP Using Web Management to Configure WDS and STP WDS and STP WDS and STP Using the CLI to Configure WDS Using the CLI to Configure STP Radio Signal Characteristics Radio InterfaceRadio Settings Using Web Management to Configure Interface Radio SettingsVlan ID Radius Attributes Number Value Radio Interface Radio Interface Radio Interface Example WEP AES-TKIPNot Supported DynamicAdmission Control No Example Long TkipRequired PRE Shared KEYAC1Background Txop Limit 0.000 ms Wi-Fi Multimedia WMM Configuration WMM OperationUsing Web Management to Configure WMM WMM Backoff Wait timesUsing the CLI to Configure WMM Ssid SW-WDSAntenna Admission Control No AC2Video Txop Limit Virtual APs VAPs Configuration Using Web Management to Configure Virtual APsRadio Interface Using the CLI to Configure Virtual APs BIT Encryption WPA-ONLYAdmission Control No Security WEPWired Equivalent Privacy WEP Using Web Management to Configure Security SettingsSecurity Page Authentication 802.1x Authentication Security Security Using the CLI to Configure WPA Pre-Shared Key Using the CLI to Configure WPA over 802.1X SecurityQuality of Service AC1Background LogCwMin LogCwMax Using the CLI to Configure Local MAC Authentication Nopassword Allowed LocalNopassword Allowed EmptySecurity Using the CLI to Configure Radius MAC Authentication Remote Using the CLI to Configure WEP Shared Key Security Shared Ssid WPATKIP-WEP Using the CLI to Configure WEP over 802.1x Security Ssid ETSAuthentication Parameters Using the CLI to Configure WPA2 Security AESWPA2-ONLY Using the CLI to Configure WPA2 Pre-Shared Key Security WPA2-PSK Status Information Status Menu DescriptionUsing Web Management to View AP Status Status Information Using the CLI to Display AP Status SQAUsing Web Management to View CDP Status Using the CLI to Display CDP Status Using Web Management to View Station Status Status Information Using Web Management to View Neighbor AP Detection Status Using the CLI to View Neighbor AP Detection Status IbssGtac LAB R2 DEMOWEP1Using Web Management to View WDS-STP Status STP Using the CLI to View WDS-STP StatusShow bridge Show bridge link Child StatusRoot Bridge Status NoneUsing Web Management to View Event Logs Using the CLI to View Event Logs RoamAbout 4102#show eventsOct 101551 Status Information Advanced Configuration Default Settings CDP WDS & STP VAP1 Nopassword Preamble Length Long Wireless Interface 802.11b/g Troubleshooting Troubleshooting StepsTroubleshooting Steps Maximum Distance Tables 80 m 264 ftMaximum Distance Tables Troubleshooting Index Radius MAC WDS 4-50bridge 4-52CLI Index-4

Related manuals

Manual 78 pages 58.85 Kb