Eaton Electrical 1250-3000 VA manual R N I N G, Contact

Page 38

INSTALLATION

W A R N I N G

The RPO/ROO circuit is an IEC 60950 safety extra low voltage (SELV) circuit. This circuit must be separated from any hazardous voltage circuits by reinforced insulation.

To install the RPO or ROO switch:

1.Verify that the UPS is off and unplugged.

2.Unscrew and remove the RPO/ROO connector from the RPO/ROO port on the UPS rear panel.

3.Refer to the following table to plan the RPO or ROO behavior:

Contact	RPO			ROO*

Open	UPS shuts down, the		indicator	UPS shuts down
Open				UPS shuts down

	illuminates

Closed	Normal operation
	To return to normal operation,
	deactivate the remote external
	contact and restart the UPS by
	pressing the	button

UPS starts up (UPS connected to AC power and AC power is available)

NOTE The local button overrides the ROO function.

4.Connect isolated, normally-closed, dry contacts (rated to handle

60 Vdc maximum, 30 Vac RMS maximum, and 20 mA maximum). Use stranded, non-shielded wiring, size 0.75 mm2–0.5 mm2 (18–20 AWG).

5.Reinstall the RPO/ROO connector to the RPO/ROO port.

6.Verify that the externally-connected RPO switch is not activated to enable power to the UPS output receptacles.

7.Plug the UPS power cord into a power outlet.

8.Press and hold the button until you hear the UPS beep (approximately one second).

9.Activate the external RPO or ROO switch to test the function. Verify the status change on the UPS front panel.

10.RPO only. De-activate the external RPO switch and restart the UPS.

32EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2 www.powerware.com

Image 38

Contents Powerware 5130 Rack/Tower UPS 1250-3000 VA User’s Guide Requesting a Declaration of Conformity Class a EMC Statements Low-Voltage Models Class B EMC Statements High-Voltage ModelsSpecial Symbols Table of Contents Specifications Troubleshooting WarrantyChapter Introduction Backed by worldwide agency approvals R N I N G Important Safety InstructionsN G E R Sikkerhedsanvisninger Vigtige Sikkerhedsanvisninger GEM Disse AnvisningerU T I O N R EBelangrijke Veiligheidsinstructies Belangrijke Veiligheidsinstructies Bewaar Deze InstructiesV a R S E L V a a RG E L E T A R a Tärkeitä Turvaohjeita Suomi Säilytä Nämä OhjeetTarkeita Turvaohjeita R O I T U SConsignes DE Sécurité Importantes Conserver CES Instructions Consignes de sécuritéR N U N G Wichtige Sicherheitsanweisungen AufbewarenSicherheitswarnungen H T U N GAvvisi di sicurezza R I C O L OV E R T E N Z a T E N Z I O N ER L I G Viktige Sikkerhetsinstruksjoner Gjem Disse InstruksjoneneViktig Sikkerhetsinformasion Regulamentos de Segurança Instruções DE Segurança Importantes Guarde Estas InstruçõesR S I K T I G I D a D OОпасно R I G OПредупреждения по мерам безопасности Предупреждение ОсторожноV E R T E N C I a Advertencias de SeguridadL I G R O Säkerhetsföreskrifter Viktiga Säkerhetsföreskrifter Spara Dessa FöreskrifterE C a U C I Ó N R aK T I G T Chapter Installation Inspecting the EquipmentItemDescription Checking the Accessory KitUPS Accessory Kit 2U models onlyVA models only Additional High-Voltage Model Accessory ItemsEBM Accessory Items Connecting the UPS Internal Battery Connecting the Internal Battery ConnectorsUPS Setup Rackmount SetupInstalling the Rail Kit Tower Setup Continue to the following section, Installing the UPS Installing the Joining Brackets Installing the UPS UPS Installation with Four EBMsInstalling a Communication Cable Installing the Power and Equipment Cords High-voltage only RPO and ROO Installation RPO/ROO ConnectionContact UPS Rear Panels 1750 VA, Low-Voltage Rear PanelRear Panel Chapter Operation Turning the UPS OnStarting the UPS on Battery Turning the UPS OffOperating Modes UPS Front PanelBattery Mode Additional UPS Features USB PortUSB Port Contact Communication Port optional Pin Number FunctionLoad Segments PowerShare Programmable ReceptacleMain Output Options Customizing the UPS with the UPS Configuration ToolFunction Factory Setting Other Available Settings Voltage Threshold OptionsUPS On/Off Options Battery OptionsUPS Sensitivity Options UPS and Battery Care Transporting the UPSReplacing Batteries When to Replace BatteriesStoring the UPS and Batteries How to Replace Internal Batteries Unscrew and remove the metal battery cover see Figure How to Replace Extended Battery Modules Recycling the Used Battery or UPS Low-Voltage Model Specifications Power Levels High-Voltage Model SpecificationsWeights and Dimensions Dimensions WxHxD WeightModel Power ConnectionsEBM Model Number Dimensions WxHxD Weight Environmental and Safety Battery+1 EBM +2 EBMs +3 EBMs +4 EBMs Battery RuntimesHalf Load Full LoadSpecifications Audible Alarms and UPS Conditions Alarm IndicatorsTroubleshooting Guide Alarm or Condition Possible Cause ActionService and Support Desk for the dealer or distributor nearest youTroubleshooting Chapter Warranty Two-Year Limited Warranty US and CanadaWarranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty Page 1642017302