Eaton Electrical 1250-3000 VA manual Chapter Operation, Turning the UPS On

Page 41

Chapter 4

Operation

This section describes:

STurning the UPS on and off

SStarting the UPS on battery

SInitiating the self-test

SOperating modes

Turning the UPS On

To turn the UPS on:

1.Plug the UPS power cord into a power outlet.

The bar graph indicators illuminate, indicating the UPS is in Standby mode.

2.Press and hold the button until you hear the UPS beep (approximately two seconds).

The alarm beeps once and all front panel indicators flash briefly. The

button and the μilluminate. Conditions permitting, the UPS

runs a battery test and the bar graph indicators cycle through. The load segment indicators (1 and 2 ) show that power is available to the output receptacles.

The bar graph indicators display the percentage of load being applied to the UPS. The UPS is now in Normal mode and supplying power to your equipment.

To change the factory-set defaults, see “Customizing the UPS with the UPS Configuration Tool ” on page 43.

3.If the indicator illuminates, see Table 17 on page 58.

NOTE The batteries charge to 90% capacity in approximately 3 hours. However, it is recommended that the batteries charge for 24 hours after installation or long-term storage.

NOTE If more than two EBMs are installed, an external battery charger is recommended for faster recharge times.

EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2	35
www.powerware.com

Image 41

Contents Powerware 5130 Rack/Tower UPS 1250-3000 VA User’s Guide Requesting a Declaration of Conformity Class B EMC Statements High-Voltage Models Class a EMC Statements Low-Voltage ModelsSpecial Symbols Table of Contents Warranty Specifications TroubleshootingChapter Introduction Backed by worldwide agency approvals R N I N G Important Safety InstructionsN G E R U T I O N Vigtige Sikkerhedsanvisninger GEM Disse AnvisningerSikkerhedsanvisninger R EV a R S E L Belangrijke Veiligheidsinstructies Bewaar Deze InstructiesBelangrijke Veiligheidsinstructies V a a RG E L E T Tarkeita Turvaohjeita Tärkeitä Turvaohjeita Suomi Säilytä Nämä OhjeetA R a R O I T U SConsignes de sécurité Consignes DE Sécurité Importantes Conserver CES InstructionsSicherheitswarnungen Wichtige Sicherheitsanweisungen AufbewarenR N U N G H T U N GR I C O L O Avvisi di sicurezzaT E N Z I O N E V E R T E N Z aR L I G Viktige Sikkerhetsinstruksjoner Gjem Disse InstruksjoneneViktig Sikkerhetsinformasion R S I K T I G Instruções DE Segurança Importantes Guarde Estas InstruçõesRegulamentos de Segurança I D a D OОпасно R I G OПредупреждения по мерам безопасности Осторожно ПредупреждениеV E R T E N C I a Advertencias de SeguridadL I G R O E C a U C I Ó N Viktiga Säkerhetsföreskrifter Spara Dessa FöreskrifterSäkerhetsföreskrifter R aK T I G T Inspecting the Equipment Chapter InstallationUPS Accessory Kit Checking the Accessory KitItemDescription 2U models onlyVA models only Additional High-Voltage Model Accessory ItemsEBM Accessory Items Connecting the Internal Battery Connectors Connecting the UPS Internal BatteryRackmount Setup UPS SetupInstalling the Rail Kit Tower Setup Continue to the following section, Installing the UPS Installing the Joining Brackets UPS Installation with Four EBMs Installing the UPSInstalling a Communication Cable Installing the Power and Equipment Cords High-voltage only RPO/ROO Connection RPO and ROO InstallationContact 1750 VA, Low-Voltage Rear Panel UPS Rear PanelsRear Panel Turning the UPS On Chapter OperationTurning the UPS Off Starting the UPS on BatteryUPS Front Panel Operating ModesBattery Mode USB Port Additional UPS FeaturesUSB Port Pin Number Function Contact Communication Port optionalProgrammable Receptacle Load Segments PowerShareFunction Factory Setting Other Available Settings Customizing the UPS with the UPS Configuration ToolMain Output Options Voltage Threshold OptionsUPS On/Off Options Battery OptionsUPS Sensitivity Options Transporting the UPS UPS and Battery CareReplacing Batteries When to Replace BatteriesStoring the UPS and Batteries How to Replace Internal Batteries Unscrew and remove the metal battery cover see Figure How to Replace Extended Battery Modules Recycling the Used Battery or UPS Low-Voltage Model Specifications Weights and Dimensions High-Voltage Model SpecificationsPower Levels Dimensions WxHxD WeightModel Power ConnectionsEBM Model Number Dimensions WxHxD Weight Battery Environmental and SafetyHalf Load Battery Runtimes+1 EBM +2 EBMs +3 EBMs +4 EBMs Full LoadSpecifications Alarm Indicators Audible Alarms and UPS ConditionsAlarm or Condition Possible Cause Action Troubleshooting GuideDesk for the dealer or distributor nearest you Service and SupportTroubleshooting Two-Year Limited Warranty US and Canada Chapter WarrantyWarranty Ten-Year Pro-Rated Limited Warranty US and Canada Warranty Load Protection Guarantee US and Canada Warranty Page 1642017302