Digi 90000583_A manual Resetting Configuration to Defaults

Page 68

7. Enter the location of the configuration file saved in step 4 and click Open.

TFTP Procedure

1.Ensure that TFTP is running on the remote host.

2.Access the web interface by entering the device server IP address in a browser’s URL window.

3.Log on to the device server as root. The default password is dbps.

4.From the main menu, choose Backup/Restore > TFTP Server.

5.Enter the name of the file and the IP address of the TFTP server and click Backup (to save the file) or Restore to apply the file.

Resetting Configuration to Defaults

To reset the configuration to defaults, follow these steps:

Note: The reset procedure causes the Digi device to lose all configuration changes. If you have a complex configuration, contact Digi before performing for information on saving your configuration. See "Reference and Certifications" on page 69 for information.

1.Use a pen, the point of a paper clip, or some other device to press the recessed button on the front panel.

2.While holding down the button, power on the Digi device.

3.When the 1-5-1 LED pattern is displayed, release the button.

Note: It may take approximately two minutes for the device to boot up.

The device boots up.

68	Chapter 11 Configuration Management

Image 68

Contents Digi TS Family 90000583A Chapter Introduction Configuring the IP AddressChapter Configuration Setting Up RealPort Special Features WirelessSpecial Features Embedded Modem Special Features Modem EmulationSpecial Features Power Over the Serial Ports Special Features IA Industrial AutomationSpecial Features Snmp Configuration ManagementDigi Contact Information About This Guide Other Documents in the LibrarySetup Overview About Configuration Methods Supported DevicesQuick Find Table Accessing the Configuration from the Web InterfaceFeature Products Availability Configuration Details DNS Introduction Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address with Digi Port Authority-Remote Configuring the IP Address Using ARP-PingConfiguring an IP Address using Dhcp and Rarp Accessing the Digi DeviceButton in the upper right corner is also available Network Settings N f i g u r a t i o nProcedure for Using a Name Server Service Base Socket Network Port Configuring the Serial PortsConfiguration Port Profiles TCP Sockets Serial Bridging Printer Industrial Automation Modem Emulation Power Management Custom User Configuration Feature DescriptionSecurity Configuration Snmp SSHSystem Configuration Click Outgoing Connections Configuring a Port for Autoconnection About AutoconnectionConfiguring a User for Autoconnection T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Configuration Considerations Select Discover Digi Device from the CDClick Network Wireless LAN Special Features Wireless Special Features Wireless E c i a l F e a t u r e s E m b e d d e d M o d e m Embedded ModemSpecial Features Embedded Modem E c i a l F e a t u r e s M o d e m E m u l a t i o n Modem EmulationModem Emulation Cable Signals Serial Device Digi DeviceOriginating, Answering, and Disconnecting Calls Scenarios for Modem EmulationModem Emulation AT Command Set Function Result ATHFunction Result CodeATP Mand state without disconnecting There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Special Features Modem Emulation Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table OUT Configuring Industrial Automation with Modbus Special Features IA Industrial AutomationPage E c i a l F e a t u r e s S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBUpgrading the Firmware Copying the Configuration to and from a Remote HostClick Backup/Restore Restore Resetting Configuration to Defaults Interpreting the LEDs Color State IndicatesSafety Statements Device EIA 232/422/485 Switch Settings FunctionRack Mounting Installation PortServer TS 16 Rack and DC Rack Specifications External WiringMechanical PortServer TS PortServer TS 2/4 Mechanical Regulatory Notices Digi One TS, PortServer TS 2/4, PortServer TS 2/4 MEI Certifications Maximum Permissible Exposure Wireless only Digi Contact Information Digi Contacts