Digi 90000583_A manual Configuring the IP Address with Digi Port Authority-Remote

Page 14

Configuring the IP Address with Digi Port Authority-Remote

Use this section to configure an initial IP address, subnet mask, and default gateway using Digi Port Authority-Remote. This procedure cannot be used to change the IP address, but only to assign the initial IP address. It also cannot be used if a DHCP server is active.

Assumptions

This procedure assumes the following:

That your Digi device supports this feature. See "Device Support: Digi Port Authority-Remoteand ARP-Ping for IP Address Configuration" on page 13.

That your Digi device is connected to the Ethernet network.

That the Digi device has DHCP client turned on. This is the default setting and it will be on unless it was turned off.

That you do not have a DHCP server to serve IP address. If you do, use the DHCP procedure. See "Configuring an IP Address using DHCP and RARP" on page 15.

That you have installed Digi Port Authority-Remote version 2.01.11 or later. Click the Help button on the tool bar in Digi Port Authority- Remote to check the version number.

Procedure

1.Run Digi Port Authority-Remote.

2.Click Discover. A list of Digi devices appears. Systems with IP addresses of 0.0.0.0 need IP addresses.

3.Select a device from the list and then click Configure.

4.Supply an IP address, subnet mask, and default gateway and then choose OK.

Digi Port Authority-Remote configures the IP address, subnet mask, and default gateway.

Configuring the IP Address Using ARP-Ping

An IP address can be configured by manually updating a server’s ARP table and then pinging the Digi device.

Note: The ARP-Ping command assigns the IP address you designate but also assigns default subnet mask and gateway addresses. It is necessary to change the subnet mask and gateway addresses.

Assumptions

This procedure assumes the following:

That your Digi device supports this feature. See "Device Support: Digi Port Authority-Remoteand ARP-Ping for IP Address Configuration" on page 13.

That your Digi device is connected to the Ethernet network

14

Chapter 2 Configuring the IP Address

Image 14
Contents Digi TS Family 90000583A Chapter Introduction Configuring the IP AddressChapter Configuration Special Features Embedded Modem Setting Up RealPortSpecial Features Wireless Special Features Modem EmulationSpecial Features Snmp Special Features Power Over the Serial PortsSpecial Features IA Industrial Automation Configuration ManagementDigi Contact Information About This Guide Other Documents in the LibrarySetup Overview About Configuration Methods Supported DevicesQuick Find Table Accessing the Configuration from the Web InterfaceFeature Products Availability Configuration Details DNS Introduction Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address with Digi Port Authority-Remote Configuring the IP Address Using ARP-PingConfiguring an IP Address using Dhcp and Rarp Accessing the Digi DeviceButton in the upper right corner is also available Network Settings N f i g u r a t i o nProcedure for Using a Name Server Service Base Socket Network Port Configuring the Serial PortsConfiguration Port Profiles TCP Sockets Serial Bridging Printer Industrial Automation Modem Emulation Power Management Custom User Configuration Feature DescriptionSecurity Configuration Snmp SSHSystem Configuration Click Outgoing Connections Configuring a Port for Autoconnection About AutoconnectionConfiguring a User for Autoconnection T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Configuration Considerations Select Discover Digi Device from the CDClick Network Wireless LAN Special Features Wireless Special Features Wireless E c i a l F e a t u r e s E m b e d d e d M o d e m Embedded ModemSpecial Features Embedded Modem E c i a l F e a t u r e s M o d e m E m u l a t i o n Modem EmulationModem Emulation Cable Signals Serial Device Digi DeviceOriginating, Answering, and Disconnecting Calls Scenarios for Modem EmulationModem Emulation AT Command Set Function Result ATHFunction Result CodeATP Mand state without disconnecting There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Special Features Modem Emulation Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table OUT Configuring Industrial Automation with Modbus Special Features IA Industrial AutomationPage E c i a l F e a t u r e s S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBUpgrading the Firmware Copying the Configuration to and from a Remote HostClick Backup/Restore Restore Resetting Configuration to Defaults Interpreting the LEDs Color State IndicatesSafety Statements Device EIA 232/422/485 Switch Settings FunctionRack Mounting Installation PortServer TS 16 Rack and DC Rack Specifications External WiringMechanical PortServer TS PortServer TS 2/4 Mechanical Regulatory Notices Digi One TS, PortServer TS 2/4, PortServer TS 2/4 MEI Certifications Maximum Permissible Exposure Wireless only Digi Contact Information Digi Contacts