Digi 90000583_A manual Specifications, External Wiring

Page 72

Do not work on your telephone wiring if you wear a pacemaker. Telephone lines carry electrical current.

Installation of inside wire may bring you close to electrical wire, conduit, terminals and other electrical facilities. Extreme caution must be used to avoid electrical shock from such facilities. You must avoid contact with all such facilities.

Telephone wiring must be at least 6 feet from bare power wiring or lightning rods and associated wires, and at least 6 inches from other wire (antenna wires, doorbell wires, wires from transformers to neon signs), steam or hot water pipes, and heating ducts.

Before working with existing inside wiring, check all electrical outlets for a square telephone dial light transformer and unplug it from the electrical outlet. Failure to unplug all telephone transformers can cause electrical shock.

Do not place a jack where it would allow a person to use the telephone while in a bathtub, shower, swimming pool, or similar hazardous location.

Protectors and grounding wire placed by the service provider must not be connected to, removed, or modified by the customer.

 

Do not touch uninsulated telephone wiring if lightning is

 

likely!

Important!

External Wiring

Any external communications wiring you may install needs to

be constructed to all relevant electrical codes. In the United

 

States this is the National Electrical Code Article 800.

 

Contact a licensed electrician for details.

Specifications

PortServer TS 8/16

Power Requirements

(Standard Models)

2-contact barrel

+9 to +30 VDC 525 mA (max) external power

connector

supply

 

 

 

 

Environmental

PortServer TS 8

PortServer TS 16

 

 

 

Ambient

0 to 50° Celsius

temperature

32 to 131° Fahrenheit

 

 

 

Relative

5% to 90% non-condensing

humidity

 

 

 

 

 

72

Chapter 12 Reference and Certifications

Image 72
Contents Digi TS Family 90000583A Configuring the IP Address Chapter ConfigurationChapter Introduction Setting Up RealPort Special Features WirelessSpecial Features Embedded Modem Special Features Modem EmulationSpecial Features Power Over the Serial Ports Special Features IA Industrial AutomationSpecial Features Snmp Configuration ManagementDigi Contact Information About This Guide Other Documents in the LibrarySetup Overview About Configuration Methods Supported DevicesAccessing the Configuration from the Web Interface Feature Products Availability Configuration DetailsQuick Find Table DNS Introduction Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address with Digi Port Authority-Remote Configuring the IP Address Using ARP-PingConfiguring an IP Address using Dhcp and Rarp Accessing the Digi DeviceButton in the upper right corner is also available Network Settings N f i g u r a t i o nProcedure for Using a Name Server Service Base Socket Network Port Configuring the Serial PortsConfiguration Port Profiles TCP Sockets Serial Bridging Printer Industrial Automation Modem Emulation Power Management Custom User Configuration Feature DescriptionSecurity Configuration Snmp SSHSystem Configuration Click Outgoing Connections Configuring a Port for Autoconnection About AutoconnectionConfiguring a User for Autoconnection T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Configuration Considerations Select Discover Digi Device from the CDClick Network Wireless LAN Special Features Wireless Special Features Wireless E c i a l F e a t u r e s E m b e d d e d M o d e m Embedded ModemSpecial Features Embedded Modem E c i a l F e a t u r e s M o d e m E m u l a t i o n Modem EmulationModem Emulation Cable Signals Serial Device Digi DeviceOriginating, Answering, and Disconnecting Calls Scenarios for Modem EmulationModem Emulation AT Command Set Function Result ATHFunction Result CodeATP Mand state without disconnecting There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Special Features Modem Emulation Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table OUT Configuring Industrial Automation with Modbus Special Features IA Industrial AutomationPage E c i a l F e a t u r e s S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBCopying the Configuration to and from a Remote Host Click Backup/Restore RestoreUpgrading the Firmware Resetting Configuration to Defaults Interpreting the LEDs Color State IndicatesSafety Statements Device EIA 232/422/485 Switch Settings FunctionRack Mounting Installation PortServer TS 16 Rack and DC Rack Specifications External WiringMechanical PortServer TS PortServer TS 2/4 Mechanical Regulatory Notices Digi One TS, PortServer TS 2/4, PortServer TS 2/4 MEI Certifications Maximum Permissible Exposure Wireless only Digi Contact Information Digi Contacts