Cypress CY7C1411BV18, CY7C1413BV18, CY7C1426BV18, CY7C1415BV18 manual DLL Timing, Static to DLL Reset

CY7C1411BV18, CY7C1426BV18

CY7C1413BV18, CY7C1415BV18

Switching Characteristics (continued)

Over the Operating Range [22, 23]

Cypress

Consortium

Description

300 MHz

278 MHz

250 MHz

200 MHz

167 MHz

Unit

Parameter

Parameter

Min

Max

Min

Max

Min

Max

Min

Max

Min

Max

Output Times

tCO

tCHQV

C/C

Clock Rise (or K/K in single

–

0.45

–

0.45

–

0.45

–

0.45

–

0.50

ns

clock mode) to Data Valid

tDOH

tCHQX

–0.45

–

–0.45

–

–0.45

–

–0.45

–

–0.50

–

ns

Data Output Hold after Output C/C

Clock Rise (Active to Active)

tCCQO

tCHCQV

Clock Rise to Echo Clock Valid

–

0.45

–

0.45

–

0.45

–

0.45

–

0.50

ns

C/C

tCQOH

tCHCQX

Clock

–0.45

–

–0.45

–

–0.45

–

–0.45

–

–0.50

–

ns

Echo Clock Hold after C/C

Rise

tCQD

tCQHQV

Echo Clock High to Data Valid

0.27

0.27

0.30

0.35

0.40

ns

tCQDOH

tCQHQX

Echo Clock High to Data Invalid

–0.27

–

–0.27

–

–0.30

–

–0.35

–

–0.40

–

ns

tCQH

tCQHCQL

HIGH [26]

1.24

–

1.35

–

1.55

–

1.95

–

2.45

–

ns

Output Clock (CQ/CQ)

tCQHCQH

tCQHCQH

CQ Clock Rise to

Clock Rise

1.24

–

1.35

–

1.55

–

1.95

–

2.45

–

ns

CQ

(rising edge to rising edge) [26]

tCHZ

tCHQZ

Rise to High-Z

–

0.45

–

0.45

–

0.45

–

0.45

–

0.50

ns

Clock (C/C)

(Active to High-Z) [27, 28]

tCLZ

tCHQX1

Rise to Low-Z [27, 28]

–0.45

–

–0.45

–

–0.45

–

–0.45

–

–0.50

–

ns

Clock (C/C)

DLL Timing

tKC Var

tKC Var

Clock Phase Jitter

–

0.20

–

0.20

–

0.20

–

0.20

–

0.20

ns

tKC lock

tKC lock

DLL Lock Time (K, C)

1024

–

1024

–

1024

–

1024

–

1024

–

Cycles

tKC Reset

tKC Reset

K Static to DLL Reset

30

30

30

30

30

ns

Notes

26.These parameters are extrapolated from the input timing parameters (tKHKH - 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (tKC Var) is already included in the tKHKH). These parameters are only guaranteed by design and are not tested in production

27.tCHZ, tCLZ, are specified with a load capacitance of 5 pF as in (b) of AC Test Loads and Waveforms. Transition is measured ± 100 mV from steady-state voltage.

28.At any voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO.

Document Number: 001-07037 Rev. *D Page 24 of 30

[+] Feedback