Cypress CY7C1387D, CY7C1386F, CY7C1387F TAP Controller State Diagram, TAP Controller Block Diagram

CY7C1386D, CY7C1386F

CY7C1387D, CY7C1387F

IEEE 1149.1 Serial Boundary Scan (JTAG) Test Data-In (TDI)

The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F incorporates a serial boundary scan test access port (TAP). This part is fully compliant with 1149.1. The TAP operates using JEDEC-standard 3.3V or 2.5V IO logic levels.

The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F contains a TAP controller, instruction register, boundary scan register, bypass register, and ID register.

Disabling the JTAG Feature

It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull up resistor. TDO can be left unconnected. Upon power up, the device will come up in a reset state which will not interfere with the operation of the device.

TAP Controller State Diagram

The TDI ball is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most signif- icant bit (MSB) of any register. (See TAP Controller Block Diagram).

Test Data-Out (TDO)

The TDO output ball is used to serially clock data out from the registers. The output is active depending upon the current state of the TAP state machine. The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. (See TAP Controller State Diagram).

TAP Controller Block Diagram

0

Bypass Register

1 TEST-LOGIC RESET

0

0 RUN-TEST/

IDLE

1	SELECT		1	SELECT
	DR-SCAN			IR-SCAN
		0			0
	1			1
	CAPTURE-DR			CAPTURE-IR
		0			0
	SHIFT-DR		0	SHIFT-IR
		1			1
	EXIT1-DR		1	EXIT1-IR
		0			0
	PAUSE-DR		0	PAUSE-IR
		1			1
	0			0
	EXIT2-DR			EXIT2-IR
		1			1
	UPDATE-DR			UPDATE-IR
	1	0		1	0

1

0

1

0

	Selection									2	1	0
TDI				Instruction Register									S election	TDO
	Circuitry
													Circuitr y
				31	30	29	.	.	.	2	1	0
			Identification Register
				x	.	.	.	.	.	2	1	0
		Boundary Scan Register
TCK
				TAP CONTROLLER
TMS

Performing a TAP Reset

A Reset is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This Reset does not affect the operation of the SRAM and may be performed while the SRAM is operating.

At power up, the TAP is reset internally to ensure that TDO comes up in a High-Z state.

The 0 or 1 next to each state represents the value of TMS at the rising edge of TCK.

Test Access Port (TAP)

Test Clock (TCK)

The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK.

Test Mode Select (TMS)

The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. This pin may be left unconnected if the TAP is not used. The ball is pulled up internally, resulting in a logic HIGH level.

TAP Registers

Registers are connected between the TDI and TDO balls and allow data to be scanned into and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction register. Data is serially loaded into the TDI ball on the rising edge of TCK. Data is output on the TDO ball on the falling edge of TCK.

Instruction Register

Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO balls as shown in the TAP Controller Block Diagram. Upon power up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section.

Document Number: 38-05545 Rev. *E Page 11 of 30

[+] Feedback