Edimax Technology AR-7286WNB user manual Access Management, Acl

Page 77

The router supports these modulations: G.Lite, T1.413, G.DMT, ADSL2, ADSL2+ and Auto-Syno Up. The router negotiates the modulation modes with the DSLAM.

The following table describes the parameters and buttons of this page:

 

Field

 

 

Description

 

 

ADSl Mode

 

 

Choose Auto Sync-Up,ADSL2+, ADSL2, G.DMT, T1.413 or

 

 

 

 

G.lite. The default is Auto Sync-Up.

 

 

 

 

 

 

 

ADSL Type

 

 

Choose ANNEX A, ANNEX I, ANNEX A/L, ANNEX M or

 

 

 

 

ANNEX A/I/J/L/M.

 

 

 

 

 

 

5.6. Access Management

In the navigation bar, click Access Management. The Access Management page that is displayed contains ACL, Filter, SNMP, UPnP, DDNS and CWMP.

5.6.1.ACL

Choose Access Management > ACL, and the page shown in the following figure appears. The user may remotely access the ADSL Router once his IP has been set as a Secure IP Address through selected applications. With the default IP 0.0.0.0, any client would be allowed to remotely access the ADSL Router.

77

Image 77
Contents AR-7286WnA / AR-7286WnB Copyright Contents Trouble Shooting System Requirements Package ContentsSafety Precautions Front Panel LED Status & Button DefinitionsWPS Rear Panel  QOS Features DMZ Connect the router to your LAN network Connect the Adsl lineConfiguration Connect the power adapter to the routerCheck the Adsl LED status PC LAN IP configuration Firewall settingsPage Page Page Windows 7, Windows Vista and Windows XP WindowsPage Page Windows Windows Vista Windows XP Page Setup Wizard EZmax Setup WizardPlease select your product Page Page Page Internet Connection Type Description PPPoE/PPPoA Bridge Mode Dynamic IP Address Static IPVCI PPoE/PPPoAVPI Bridge Mode Dynamic IP Address Static IP Adsltyperoutervcmux Firmware UpgradePage Device Info Accessing the RouterStatus System Log Adsl Statistics StatisticsEthernet Statistics Wlan Statistics Quick StartPage Auto setup by ISP list ISP Field DescriptionDynamic IP Address Static IP Address Bridge ModePPPoE/PPPoA Internet Interface SetupCBR, UBR, rtVBR, or nrtVBR ATMSCR PCRMBS Select IPv4 , IPv4/IPv6 or IPv6You can choose Activated or Deactivated VC-Mux,1483 Routed IP LLCIPoA or 1483 Routed IP VC-MuxIPv4 Address NATDual Stack Lite IPv6 AddressIPv4 Options IPv6 Options You can select None , Both , in Only or OUT OnlySelect Activated or Deactivated You can select None, Both, in Only or OUT Only Field Description Connection SettingRecommended Connect On-Demand or Connect Manually You can choose 1483 Bridged IP LLC or 1483 Bridged Field Description Dual Stack LiteLAN Dhcp You may choose ManagedAddr or Other Config Select Enable or DisablePage You may choose Activated or Deactivated WirelessField Description Access Point Settings Even numbers only 802.11b+g, 802.11n, 802.11g+n or 802.11b+g+n 11n SettingsMultiple SSIDs Settings WPS Settings Advanced SetupSelect from Disabled , WEP-64Bits , WEP-128Bits Wireless MAC Address FilterRouting FirewallNAT Address Mapping for Multiple IP Service DMZ Field Description Choose the One-to-One , Many-to-One , Many-to-Many QoSOverload , Many-to-Many No Overload , or Server IP Version IPv4Rule Field Description Quality of ServiceMAC IP Version IPv6 DscpSelect Low , Medium , High or Highest You may select Activated or Deactivated . Activated must IPv6Vlan Page Vlan ID AdslChoose Annex a , Annex I , Annex A/L , Annex M or Access ManagementACL Support Web , FTP , Telnet , Snmp , Ping or AL L FilterChoose Both, Incoming or Outgoing Support IP / MAC Filter, Application Filter and URLFilter MSN ICQYmsg URL FilterURL SnmpUPnP Cwmp DdnsURL for the CPE to connect to the ACS using the CPE WAN Time Zone MaintenanceAdministration Firmware SysRestart UpgradeDiagnostics 255.255.255.0, respectively Question AnswerWeee Directive & Product Disposal EU Declaration of ConformityDeclaration of Conformity