Ericsson LBI-39076B system manual Who Can Receive Calls

Page 31

CONFIGURATION

LBI-39076B

∙Line Active - This column of parameters defines (for the site) if a line is available for interconnect calls. Default is no (N) for all lines. Enter Y for yes, or leave N for no. Note that a line number gets its number from the radio channel number that shares the same GTI Unit. Also note that GTI Units are placed on the highest available channel numbers first.

Line Definition (menu selection 14) Line Parameters (pages 1 & 2)

∙Pulse Dial - This column of parameters defines (for the site) if a line uses pulse dialing. Default is no (N) for all lines. Note that the ELI system will ignore this parameter, so there is no point in changing it from its

default value. However, the equivalent of this parameter must be set in the GTI user database. (See the GTI Configurator Software user’s guide, LBI- 39077.)

Line Definition (menu selection 14) Line Parameters (pages 1 & 2)

∙Message Conv Limit - This 4-digit field defines (for the site) the conversation time limit(in seconds) for interconnect calls (and message trunking). Default is 300 seconds. Enter a number from 10 to 2550.

Site/Device Definition (menu selection 10) Site Parameters (panel 2)

Channel Assignment Parameters

∙Interconnect Hang Time - This 2-digit field defines (for the site) the time (in seconds) between an unkey command and channel drop. Default is 30 seconds. Do not enter a number larger than 60 (see note).

Site/Device Definition (menu selection 10) Site Parameters (panel 2)

Channel Assignment Parameters

NOTE

Although the Interconnect Hang Time (IHT) can be set higher than 60 seconds, the GTI unit will wait no more than 60 seconds for a telephone- originated call to be answered. Therefore, setting the IHT to more than 60 seconds will not allow more than 60 seconds for the call to be answered.

NOTE

The voice prompt played to the caller (as the result of an unanswered telephone-originated call) will depend upon whether the IHT or the 60-second GTI interval expires first. If the IHT is set to less than 60 seconds, it will expire first and the GTI unit will play voice prompt #6. (Default = Call is disconnecting) If the IHT is set to more than 60 seconds, the 60-second GTI interval will expire first and the GTI unit will play voice prompt #5. (Default = Radio didn’t answer) If the IHT is set exactly to 60 seconds, either voice prompt #5 or #6 may be played, due to slight timing variances.

∙Max # Concurrent Intercon - This 2-digit field defines (for the site) the maximum number of simultaneous telephone interconnect calls permitted. Default is 2.

Site/Device Definition (menu selection 10) Site Parameters (panel 2)

Channel Assignment Parameters

Who Can Receive Calls

∙Inb Interconnect - This 1-digit field defines (for each logical unit ID) if inbound interconnect calls are allowed for this specific logical unit ID. Default is no

(N). Enter Y for yes, or leave N for no.

Logical Unit Definition (menu selection 11) Radio Parameters (panel 2)

Radio Features

∙Inb Interconnect - This 1-digit field defines (for each group ID) if inbound interconnect calls are allowed for this specific group ID. Default is no (N). Enter Y for yes, or leave N for no.

Group Definition (menu selection 12) Group Parameters (panel 2)

Features

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents System Manual Revision Date Reason for Change Revision HistoryTable of Contents Table of Contents List of Figures and Tables FiguresFigures and Tables Regulatory Compliance DOC Compliance Notice DOC RegistrationDOC Avis DE Conformation Specifications SpecificationsMastr Overview Introduction / DescriptionGTI Units DescriptionIAM Description / InstallationGTI Configurator Software GTI Interface BoardGetc InstallationMDR GTIEmpty Radio SoftwareSite Controller Hardware Site Controller SoftwareApplication Software PROMs Radio Channel AssignmentsPersonality PROMs Main Board GTI SoftwareRevision-A Main boards Processor Board Revision-D or E Main boardsInterface Board OUT GTI Telephone InterfaceRevision-A Main Board F2&F3Wire E&M, Type Wire E&M, MicrowaveEnd-to-End, Loop Start End-to-End, Ground Start Jumper Positions for JP1 Through JP15 Fuses External JP4 Lead Fuse F2 Reference DS1 Revision-D or E Main Board GTI DIP Switch SettingsDid GTI Interface Board Mounting GTI Connections GTI & IAM MountingTelephone Line Mastr II or IIe Power Supply/Audio Mastr III Power Supply/AudioPCM/Data Bus Site Controller Computer IAM SoftwarePrinter RS-232 Port Power SupplyAlarm Outputs IAM ConnectionsGetc Modification IAM DIP Switch SettingsOperation without System Manager ConfigurationSite Controller Database Interconnect Timing ParametersGeneral Limits for Site Operation with System ManagerWho Can Receive Calls Who Has What Toll Call Restrictions Who Has What PriorityGTI Database RecommendationRTS CTS Remote Data LinkOperation Printer Indicator CDR Received IndicatorAlarm Indicator Low-Battery IndicatorOverview BackupInterconnect Calls StatusDetecting the Call Telephone-Originated CallAnswering the Call Obtaining Working Channel Identifying Called IDRadio-Originated Call Ending the CallObtaining a Working Channel RE-DIALED Digits Interconnect DigitsOverdialed Digits Mastr III Repeaters MaintenanceGTI Removal Mastr II or IIe RepeatersGTI DSP ELI Software UpgradesPlan a All at One Time Software Version Required for Main Board Revision NumberPlan B Half at a Time Maintenance Plan C One at a Time Maintenance IAM Unit No interconnect or radio-to-radio TroubleshootingSet the Max # Concurrent Intercon Interconnect Rotary Definition forAll telephone-originated interconnect Toll Call Parameters screen LBI-39076B Glossary GlossaryPresence of a DC loop current between one of the two wires Parts List Glossary / Parts ListEdacs Interconnection DiagramSchematic Diagram Installation Checklist Installation Checklist
Top Page Image Contents