Technics MT5634SMI-34, MT5634SMI-92 manual Lsltcq, Enable Report Description

Page 55

Chapter 6 – Voice Commands

MP-LPC/Author

Multi-pulse LPC

LSLTCQ

Least Squares Lattice Trellis Coded Quantization

IS-101 does not make any provisions for standard compression modifiers.

Command:

+VTD=<dur>

Select Default Beep Tone Duration Timer (DTMF/Tone

 

 

Generation Duration)

Result Codes:

OK if the modem accepts the command; ERROR if the parameter is out of range.

Description:

The +VTD= command causes the modem to set the default DTMF/tone generation duration used

 

with the +VTS command. This command does not affect the ATD command settings. The <dur>

 

parameter range is given by the +VTD=? command, in units of 0.01 seconds. A setting of +VTD=0

 

specifies a manufacturer-specific time interval.

Command:

+VDR=<enable>,<report>

Enable/Disable Distinctive Ring (Ring Cadence Reporting)

Values:

See the Description

 

Result Codes:

OK if the modem accepts the command; ERROR if the parameter is out of range.

Description:

The +VDR command causes the modem to enable or disable reporting of the ring cadence

 

information, and to control the timing of the Ring event code report if ring cadence reporting is

 

enabled.

 

 

This report format is one line per silence period, and one line per ring period. The length of the

 

silence period is in the form DROF=<number in units of 0.1 seconds><CR><LF>, and the length of

 

the ring in the form DRON=<number in units of 0.1 seconds>. The <LR> character is optional. The

 

modem may produce a Ring event code after the DRON message if enabled by the <report>

 

parameter. The <report> parameter should be set to a value larger than the expected off-times

 

within a single pattern so that the Ring event reports are issued only during the off-times between

 

the complex patterns.

 

<enable>

<report>

Description

0

n/a

The modem will not generate ring cadence reports. Other call progress

 

 

event codes (including Ring) are reported as normal.

1

0

The modem only produces DROF and DRON messages. Other call

 

 

progress result codes (including RING) are reported as normal.

1

non-zero

The modem only produces DROF and DRON messages. The RING result

 

 

code is displayed after the falling edge of the ring pulse (i.e., after the

 

 

DRON report).

2–255

non-zero

Reserved for future standards.

Example: The lines below shows a cadence with an off time of 4.0 seconds, an on time of 0.8 seconds, an off time of 0.4 seconds, and an on time of 0.8 seconds. The RING result code is displayed 0.5 seconds after the last DRON message. The command to enable this sample sequence is +VDR-1,5 , as shown below:

<DLE><X>

DROF=40

DRON=8

DROF=4

DRON=8

RING <DLE><.> <DLE><X> DROF=40 DRON=8 DROF=4 DRON=8

RING <DLE><.>

Command:

+VDT=<enable>,<report>

Control Tone Cadence Reporting

Result Codes:

OK if the modem accepts the command; ERROR if the parameter is out of range.

Description:

The +VDT command causes the modem to enable or disable reporting of the control tone cadence

 

information in the frequency band used by the Ring Back/Remote Ring, Busy, and Reorder/Fast

 

Busy tones (usually in the 300 - 600 Hz range). This reporting is subject to the tone detection

 

restrictions reported by the +VLS=? command.

SocketModem Global MT5634SMI Developer’s Guide

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents MT5634SMI-34 MT5634SMI-92 Revisions Table of Contents Multi-Tech’s Flash Programming Protocol Appendix C Country Configuration and Result Codes Index Introduction Product Description SpecificationsProduct Description MT5634SMI Features MatrixTIA/EIA TR29.2 Technical Specifications and FeaturesStandard MT5634SMI-IT-92 Industrial Temperature 3.3V Build OptionPhysical Dimensions All Models Mechanical SpecificationsPin # Signal Name I/O Type Description Pin ConfigurationsDigital Ground Active High RDX status Tip Signal from TelcoRing Signal from Telco Active High DCD statusVCC PWR Pin # Signal Description NameDgnd GND INTElectrical Characteristics Electrical CharacteristicsTiming Requirements for Parallel Read Handling PrecautionsTiming Requirements Timing Requirements for Parallel WriteSocketModem Parallel Interface Internal Registers SocketModem Parallel Interface a Programmer’s DescriptionSocketModem Mimic MMM Operation Register Name Register Description Host Access Special Register Set Note *2 Time Out InterruptsRegister Functional Descriptions Internal RegistersTHR Transmit Holding Register TX Fifo IER Interrupt EnableBit Priority Interrupt Source Interrupt Reset Control RBR Receive Buffer RX FifoLCR Line Control FCR Fifo ControlMCR Modem Control MSR Modem Status LSR Line StatusBaud Rate Clock Divisor Decimal DLM Value HEX DLL Value HEX SCR ScratchDLL Divisor Latch LSByte DLM Divisor Latch MSByteAT Command Summary AT Commands, S-Registers Result CodesSet Register Value Modulation HandshakeDS= y Dial Stored Telephone Number AT CommandsEnter Key Dial string modifiersReturn Online to Data Mode Sr? Sr= n Set Register ValueXON/XOFF Pacing Control \An Select Maximum MNP Block Size Zy=x Store Dialing Command\Bn Transmit Break Data mode. The modem receives the break from the computer \Nn Error Correction Mode Selection\Tn Inactivity Timer \Kn Break Control\Xn XON/XOFF Pass-Through DCn AT Command Control$MBn Online BPS Speed $RPn Ring Priority vs. AT Command Priority$Dn DTR Dialing $EBn Asynchronous Word Length#CBNy=x Store Callback Password #CBDn Callback DelayCallback Failed Attempts Reset #CBIn Local Callback Inactivity TimerEscape AT Commands Modulation Possible rates bps1 Commands+MS= Modulation Selection Subparameters+PIG=n PCM Upstream Ignore +PCW=n Call Waiting Enable+PMH=n Modem on Hold Enable Mod value Valid maxrate values bps+PMHF V.92 Modem Hook Flash +PMHT=n Modem on Hold Timer+PMHR=n Modem on Hold Initiate +VCID=n Caller ID Selection +PQC=n Quick Connect Control#S=x Store Setup Password #Sx Enter Setup PasswordRegisters Register Unit Range Default DescriptionS48=7 S48=128 S38Terse Verbose Description Result Codes111 Voice Commands Commands That Change for Voice Mode Support Voice CommandsVoice S-Register Summary +FCLASS= mode Enter Select Modem Operating Mode Voice +V Commands SummaryVoice +V Commands Detail Command DescriptionAT+FCLASS=? Enter Display Service Class Capabilities Touch Tone Signals Digit Low frequency High frequency+FCLASS=8 Dtmf Detect Detect and Control Dtmf +FMR?Enter Report Version Level +VNH=hookEnter Automatic Hang-Up Control+FMI?Enter Report Manufacturers ID +FMM?Enter Report Product IDEnter Voice Receive State +VTS=string Produce Dtmf and Tone Generation in Voice Mode+VGR=gain Set the Gain for Received Voice Samples +VTS=? Report Frequency SupportAT+VTS=? Start Voice Transmission ProcessCode Description +VGT=level Set the Volume for Transmitted Voice Samples+VIT=timer Set DTE/DCE Inactivity Timer +VLS=label Select Analog Source/Destination +VRA=interval Set Ring Back Goes Away Timer +VSD=sds,sdi Set Silence Detection Sensitivity +VRN=interval Set Ring Back Never Appeared Timer+VSM=cml,vsr,scs,sel Select Voice Compression Method AT+VSM=? +VSM=? Report Voice Compression MethodIdentifier Description +VDT=enable,report Control Tone Cadence Reporting Enable Report DescriptionLsltcq +VEM=? Report Event Reporting and Masking Capabilities +VEM=mask Event Reporting and MaskingAT+VBT=? Interface Configuration Commands+VPP=enable Enable or Disable Voice Mode Packet Protocol +VBT=? Report Modem Flow Control Assert and Deassert PointsFlow Control Voice Mode Result Codes+VPR=rate Select DTE/DCE Interface Rate Turn Off Autobaud Valid Complex Event Report Tags Unsolicited Voice Mode Result CodesTag Description Shielded Code Hex Event Report Description Voice Mode Shielded CodesAscii Sample Sessions Command ResponseSample Rate Selection and Suggested Compression Method AT+VLS=0 AT+VLS=4AT+VTX DLE ETXAT+VNH=1 AT+VLS=2AT+VRX DLE NULRelated Manuals DTE/DCE Interface RatesAdditional Information Fax Commands Setup Remote Configuration Country Code ConfigurationRemote Configuration Basic ProcedureCountry AT Command Result Code Hexadecimal Decimal Country Code ConfigurationUsing the Global Wizard Utility Using AT CommandsUpgrade Overview Firmware Upgrade ProcedureUpgrade Steps Identify the Current Version of the Firmware Download the Upgrade FileInstall the Flash Wizard Extract the Firmware Upgrade .Hex FilesUsing the Flash Wizard Upgrade the Modem’s FirmwareRestore Your Parameters Handshake Sequence Multi-Tech Systems, Inc. Flash Programming ProtocolProgramming the Modem Modem CommentsOther Programming Concerns Other Supported Boot Code CommandsATI4 End of File Record Char Pos Field Type Value Description Intel Hex FormatData Record Char Pos Field Type Value Description Example Extended Address Record in Intel FormatExample End of File in Intel Format Serial Test/Demo Board Components Appendix a Mechanical Details5V / 3.3V Jumper JP1 Serial Test/Demo Board Block DiagramAddress/COM Port/ IRQ Select Jumpers JP2 and JP3 Parallel Test/Demo Board ComponentsOperating Voltage Select Jumper JP4 Figure A-4. Parallel Test/Demo Board Block Diagram Parallel Test/Demo Board Block DiagramTelecom Approvals Safety and EMC ApprovalsHardware Considerations Regulatory Design ConsiderationsSafety 5V Tolerant Inputs for 3.3V Modules Industry Canada FCC Part 15 RegulationTelecom Labeling Requirements FCC Part 68 TelecomReregistration From FCC Part 68 Subpart D Conditions for RegistrationCanadian Limitations Notice Fax Branding StatementMultiple Listing EMC, Safety, and R&TTE Directive ComplianceIndustry Canada CS-03 International Modem RestrictionsSouth African Notice New Zealand Telecom Warning NoticeCountry Country Config. hex ATI9 Response Appendix C Country Configuration Result CodesAppendix C Country Configuration and Result Codes Appendix C Country Configuration and Result Codes Appendix C Country Configuration and Result Codes Page Index Index Index Index
Top Page Image Contents