Technics MT5634SMI-92, MT5634SMI-34 manual Result Codes, Terse Verbose Description

Page 42

Chapter 5 – AT Commands, S-Registers, and Result Codes

Result Codes

In command mode your modem can send responses called Result Codes to your computer. Result codes are used by communications programs and can also appear on your monitor.

Terse

Verbose

Description

0

OK

Command executed

1

CONNECT

Modem connected to line

2

RING

Ring signal detected

3

NO CARRIER

Carrier signal lost or not detected

4

ERROR

Invalid command

5 *

CONNECT 1200

Connected at 1200 bps

6

NO DIALTONE

No dial tone detected

7

BUSY

Busy signal detected

8

NO ANSWER

No answer at remote end

9

CONNECT 75

Connected at 75 bps

10*

CONNECT 2400

Connected at 2400 bps

11*

CONNECT 4800

Connected at 4800 bps

12*

CONNECT 9600

Connected at 9600 bps

13*

CONNECT 14400

Connected at 14400 bps

14*

CONNECT 19200

Connected at 19200 bps

18

CONNECT 57600

Connected at 57600 bps

24*

CONNECT 7200

Connected at 7200 bps

25*

CONNECT 12000

Connected at 12000 bps

28

CONNECT 38400

Connected at 38400 bps

40*

CONNECT 300

Connected at 300 bps

55*

CONNECT 21600

Connected at 21600 bps

56*

CONNECT 24000

Connected at 24000 bps

57*

CONNECT 26400

Connected at 26400 bps

58*

CONNECT 28800

Connected at 28800 bps

59*

CONNECT 31200

Connected at 31200 bps

60*

CONNECT 33600

Connected at 33600 bps

70

CONNECT 32000

Connected at 32000 bps

71

CONNECT 34000

Connected at 34000 bps

72

CONNECT 36000

Connected at 36000 bps

73

CONNECT 38000

Connected at 38000 bps

74

CONNECT 40000

Connected at 40000 bps

75

CONNECT 42000

Connected at 42000 bps

76

CONNECT 44000

Connected at 44000 bps

77

CONNECT 46000

Connected at 46000 bps

78

CONNECT 48000

Connected at 48000 bps

79

CONNECT 50000

Connected at 50000 bps

80

CONNECT 52000

Connected at 52000 bps

81

CONNECT 54000

Connected at 54000 bps

82

CONNECT 56000

Connected at 56000 bps

83

CONNECT 58000

Connected at 58000 bps

84

CONNECT 60000

Connected at 60000 bps

86

CONNECT 16800

Connected at 16800 bps

87

CONNECT 115200

Connected at 115200 bps

88

DELAYED

Delay is in effect for the dialed number

89

BLACKLISTED

Dialed number is blacklisted

90

BLACKLIST FULL

Blacklist is full

91

CONNECT 230400

Connected at 230400 bps

100

CONNECT 28000

Connected at 28000 bps

101

CONNECT 29333

Connected at 29333 bps

102

CONNECT 30666

Connected at 30666 bps

103

CONNECT 33333

Connected at 33333 bps

104

CONNECT 34666

Connected at 34666 bps

105

CONNECT 37333

Connected at 37333 bps

106

CONNECT 38666

Connected at 38666 bps

107

CONNECT 41333

Connected at 41333 bps

108

CONNECT 42666

Connected at 42666 bps

109

CONNECT 45333

Connected at 45333 bps

110

CONNECT 46666

Connected at 46666 bps

SocketModem Global MT5634SMI Developer’s Guide

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents MT5634SMI-34 MT5634SMI-92 Revisions Table of Contents Multi-Tech’s Flash Programming Protocol Appendix C Country Configuration and Result Codes Index Product Description Specifications IntroductionProduct Description Features Matrix MT5634SMITechnical Specifications and Features TIA/EIA TR29.2MT5634SMI-IT-92 Industrial Temperature 3.3V Build Option StandardMechanical Specifications Physical Dimensions All ModelsPin Configurations Pin # Signal Name I/O Type DescriptionDigital Ground Active High DCD status Tip Signal from TelcoRing Signal from Telco Active High RDX statusINT Pin # Signal Description NameDgnd GND VCC PWRElectrical Characteristics Electrical CharacteristicsTiming Requirements for Parallel Write Handling PrecautionsTiming Requirements Timing Requirements for Parallel ReadSocketModem Parallel Interface a Programmer’s Description SocketModem Parallel Interface Internal RegistersSocketModem Mimic MMM Operation Register Name Register Description Host Access Internal Registers Time Out InterruptsRegister Functional Descriptions Special Register Set Note *2RBR Receive Buffer RX Fifo IER Interrupt EnableBit Priority Interrupt Source Interrupt Reset Control THR Transmit Holding Register TX FifoFCR Fifo Control LCR Line ControlMCR Modem Control LSR Line Status MSR Modem StatusDLM Divisor Latch MSByte SCR ScratchDLL Divisor Latch LSByte Baud Rate Clock Divisor Decimal DLM Value HEX DLL Value HEXAT Commands, S-Registers Result Codes AT Command SummaryModulation Handshake Set Register ValueDial string modifiers AT CommandsEnter Key DS= y Dial Stored Telephone NumberReturn Online to Data Mode Sr= n Set Register Value Sr?XON/XOFF Pacing Control Zy=x Store Dialing Command \An Select Maximum MNP Block Size\Bn Transmit Break \Kn Break Control \Nn Error Correction Mode Selection\Tn Inactivity Timer Data mode. The modem receives the break from the computerDCn AT Command Control \Xn XON/XOFF Pass-Through$EBn Asynchronous Word Length $RPn Ring Priority vs. AT Command Priority$Dn DTR Dialing $MBn Online BPS Speed#CBIn Local Callback Inactivity Timer #CBDn Callback DelayCallback Failed Attempts Reset #CBNy=x Store Callback PasswordEscape AT Commands Subparameters Commands+MS= Modulation Selection Modulation Possible rates bps1Mod value Valid maxrate values bps +PCW=n Call Waiting Enable+PMH=n Modem on Hold Enable +PIG=n PCM Upstream Ignore+PMHT=n Modem on Hold Timer +PMHF V.92 Modem Hook Flash+PMHR=n Modem on Hold Initiate +PQC=n Quick Connect Control +VCID=n Caller ID Selection#Sx Enter Setup Password #S=x Store Setup PasswordRegister Unit Range Default Description RegistersS38 S48=7 S48=128Result Codes Terse Verbose Description111 Voice Commands Voice Commands Commands That Change for Voice Mode SupportVoice S-Register Summary Command Description Voice +V Commands SummaryVoice +V Commands Detail +FCLASS= mode Enter Select Modem Operating ModeTouch Tone Signals Digit Low frequency High frequency AT+FCLASS=? Enter Display Service Class Capabilities+FCLASS=8 Dtmf Detect Detect and Control Dtmf +FMM?Enter Report Product ID +VNH=hookEnter Automatic Hang-Up Control+FMI?Enter Report Manufacturers ID +FMR?Enter Report Version Level+VTS=string Produce Dtmf and Tone Generation in Voice Mode Enter Voice Receive StateStart Voice Transmission Process +VTS=? Report Frequency SupportAT+VTS=? +VGR=gain Set the Gain for Received Voice Samples+VLS=label Select Analog Source/Destination +VGT=level Set the Volume for Transmitted Voice Samples+VIT=timer Set DTE/DCE Inactivity Timer Code Description+VRA=interval Set Ring Back Goes Away Timer +VRN=interval Set Ring Back Never Appeared Timer +VSD=sds,sdi Set Silence Detection Sensitivity+VSM=cml,vsr,scs,sel Select Voice Compression Method +VSM=? Report Voice Compression Method AT+VSM=?Identifier Description Enable Report Description +VDT=enable,report Control Tone Cadence ReportingLsltcq +VEM=mask Event Reporting and Masking +VEM=? Report Event Reporting and Masking Capabilities+VBT=? Report Modem Flow Control Assert and Deassert Points Interface Configuration Commands+VPP=enable Enable or Disable Voice Mode Packet Protocol AT+VBT=?Voice Mode Result Codes Flow Control+VPR=rate Select DTE/DCE Interface Rate Turn Off Autobaud Unsolicited Voice Mode Result Codes Valid Complex Event Report TagsTag Description Voice Mode Shielded Codes Shielded Code Hex Event Report DescriptionAscii Command Response Sample SessionsSample Rate Selection and Suggested Compression Method DLE ETX AT+VLS=4AT+VTX AT+VLS=0DLE NUL AT+VLS=2AT+VRX AT+VNH=1DTE/DCE Interface Rates Related ManualsAdditional Information Fax Commands Basic Procedure Remote Configuration Country Code ConfigurationRemote Configuration SetupUsing AT Commands Country Code ConfigurationUsing the Global Wizard Utility Country AT Command Result Code Hexadecimal DecimalFirmware Upgrade Procedure Upgrade OverviewUpgrade Steps Extract the Firmware Upgrade .Hex Files Download the Upgrade FileInstall the Flash Wizard Identify the Current Version of the FirmwareUpgrade the Modem’s Firmware Using the Flash WizardRestore Your Parameters Modem Comments Multi-Tech Systems, Inc. Flash Programming ProtocolProgramming the Modem Handshake SequenceOther Supported Boot Code Commands Other Programming ConcernsATI4 Example Extended Address Record in Intel Format Intel Hex FormatData Record Char Pos Field Type Value Description End of File Record Char Pos Field Type Value DescriptionExample End of File in Intel Format Appendix a Mechanical Details Serial Test/Demo Board ComponentsSerial Test/Demo Board Block Diagram 5V / 3.3V Jumper JP1Parallel Test/Demo Board Components Address/COM Port/ IRQ Select Jumpers JP2 and JP3Operating Voltage Select Jumper JP4 Parallel Test/Demo Board Block Diagram Figure A-4. Parallel Test/Demo Board Block DiagramSafety and EMC Approvals Telecom ApprovalsRegulatory Design Considerations Hardware ConsiderationsSafety 5V Tolerant Inputs for 3.3V Modules FCC Part 15 Regulation Industry CanadaFCC Part 68 Telecom Telecom Labeling RequirementsFrom FCC Part 68 Subpart D Conditions for Registration ReregistrationFax Branding Statement Canadian Limitations NoticeInternational Modem Restrictions EMC, Safety, and R&TTE Directive ComplianceIndustry Canada CS-03 Multiple ListingNew Zealand Telecom Warning Notice South African NoticeAppendix C Country Configuration Result Codes Country Country Config. hex ATI9 ResponseAppendix C Country Configuration and Result Codes Appendix C Country Configuration and Result Codes Appendix C Country Configuration and Result Codes Page Index Index Index Index
Top Page Image Contents