UTStarcom UT-300R2 manual Tftp

Page 81

Chapter 8 Attachments

81

ATM Cell format

ITU-T Rec. I.361

 

 

OAM support

F4/F5 Loopback

 

 

ATM QoS (Traffic

UBR, CBR, VBR-rt, VBR-nrt

Shaping)

 

 

 

Point-to-Point

RFC1661

Protocol

 

 

 

PPP over ATM

RFC2364

 

 

PPP over Ethernet

RFC2516

 

 

User Authentication

PAP (RFC 1334), CHAP (RFC 1994)

 

 

VPN Pass Through

IPSec/L2TP/PPTP pass through

 

 

IP Filtering

IP Filtering

 

 

 

MAC Filtering

 

 

 

URL Filtering

 

 

 

Domain Blocking

 

 

SPI

Detection of Known Attacks

 

 

Administration

Username/Password control for Telnet,

WEB configuration

 

 

 

HTTP Server

For WEB-based management

 

 

Telnet

Through LAN with user name/password

 

 

TFTP

For firmware upgrade

 

 

SNMP v.1 and v.2c

MIB II (RFC 1213)

 

 

Remote

Management from WAN

Management

 

 

 

Page 80 Page 82
Image 81
Page 80 Page 82
Contents UT-300R2 ADSL2/2+Modem United States Government Legends Contents UT-300R2 Status Information Attachments Device Introduction OverviewDevice Appearance FeaturesOverview Packing List Installation PlanningFront Panel Interfaces IntroductionConnecting the Adsl Line Cable ConnectionsRear Panel Connecting the UT-300R2 to the Ethernet LAN Computer to UT-300R2 Connection Hub or Switch to UT-300R2 ConnectionPower on Installation Planning Set up TCP/IP on Your PC Before Configuring UT-300R2Configure IP Settings on Your PC Set up Proxy ServiceFirst Time Log on Summary Web-based ManagementWeb-based Management Options of Web-based Configuring the WAN ConnectionWeb-based Management WAN Setting − Add menu Configuring a Bridged Connection for the WANDepending on which WAN Type and Connection Type you select Web-based Management Configuring a Routed/Bridged Connection for the WAN WAN Settings Menu Routed/Bridged Mode Configuring a PPP Connection for the WAN Web-based Management Dynamic IP Address for the WAN Connection Web-based Management Static IP Address for WAN Web-based Management Dhcp Configuration Dhcp Server Settings for the LAN DNS Server Setting Use the UT-300R2 for DhcpDisabling the Dhcp Server Configuring the LAN Connection Web-based Management Save New Settings Web-based Management Advanced Configuration / Network Management Advanced configuration menus NAT Virtual Server ConfigurationAdvanced Configuration / Network Management Advanced Configuration / Network Management Directory Configuration and Read-only Menus Special Application Configuration Directory Configuration and Read-only Menus This is the TCP or UDP port number that will be used Configure a Filter Rule-IP Filters Advanced Configuration / Network Management Advanced Configuration / Network Management MAC Select Allow to permit packets to pass through Configuring a Filter Rule- MAC Filters Advanced Configuration / Network Management Directory Configuration and Read-only Menus Configuring a Filter Rule-URL Blocking Advanced Configuration / Network Management Directory Configuration and Read-only Menus Configuring a Filter Rule-Domain Blocking Advanced Configuration / Network Management This radio button selects the URL filter rule Firewall Firewall Configuration MenuAttacks Port Scans DMZ Ddns RIP Tools Administrator’s SettingsAdministrator Settings Menu Configure System TimeSave UT-300R2 Configuration Settings Save Configuration File to PC System Settings Load Saved Configuration FilesFirmware Update Restore Factory Default SettingsTools Log UT-300R2 Status InformationTraffic Statistics Traffic StatisticsDiagnostics DiagnosticsAttachments Technical SpecificationsSafety and Environmental Tftp Glossary Attachments
Top Page Image Contents