UTStarcom UT-300R2 manual Select Allow to permit packets to pass through

Page 54

52 Chapter 5 Advanced Configuration / Network Management

Directory

Configuration and Read-only Menus

 

 

 

Select Allow to permit packets to pass through the

Action

UT-300R2 if they meet the criteria of this rule, and

Deny dropping packets that meet the criteria of this

 

 

rule.

 

 

 

When LAN is specified in the Interface drop-down

 

menu, this filter will apply to packets that have one

 

of the specified IP addresses as their source, and

 

are sent from a PC on your LAN.

 

When WAN is specified in the Interface drop-down

Source

menu, this filter will apply to packets that have one

 

of the specified IP addresses as their source, and

 

are sent from a PC on the WAN (Internet).

 

If Both is selected, then this rule will apply to

 

packets that are sent from PCs on both the WAN

 

and your LAN.

 

 

 

When LAN is specified in the Interface drop-down

 

menu, this filter will apply to packets that have one

 

of the specified IP addresses as their destination,

 

and are being sent to a PC on your LAN.

 

When WAN is specified in the Interface drop-down

Destination

menu, this filter will apply to packets that have one

 

of the specified IP addresses as their destination,

 

and are being sent to a PC on the WAN (Internet).

 

If Both is selected, then this rule will apply to

 

packets that are being sent to PCs on both the

 

WAN and your LAN.

 

 

Source

The Source Port is the TCP/UDP port on either the

LAN or WAN depending on if you are configuring

Port

an Outbound or Inbound Filter rule.

 

 

 

Destination

The Destination Port is the TCP/UDP port on either

Port

the LAN or WAN

 

 

Protocol

Select the transport protocol (TCP, UDP, ICMP, or

All) that will be used for the filter rule.

 

 

 

Image 54
Contents UT-300R2 ADSL2/2+Modem United States Government Legends Contents UT-300R2 Status Information Attachments Overview Device IntroductionFeatures Device AppearanceOverview Installation Planning Packing ListInterfaces Introduction Front PanelConnecting the Adsl Line Cable ConnectionsRear Panel Connecting the UT-300R2 to the Ethernet LAN Hub or Switch to UT-300R2 Connection Computer to UT-300R2 ConnectionPower on Installation Planning Before Configuring UT-300R2 Set up TCP/IP on Your PCSet up Proxy Service Configure IP Settings on Your PCFirst Time Log on Web-based Management SummaryWeb-based Management Configuring the WAN Connection Options of Web-basedWeb-based Management Configuring a Bridged Connection for the WAN WAN Setting − Add menuDepending on which WAN Type and Connection Type you select Web-based Management Configuring a Routed/Bridged Connection for the WAN WAN Settings Menu Routed/Bridged Mode Configuring a PPP Connection for the WAN Web-based Management Dynamic IP Address for the WAN Connection Web-based Management Static IP Address for WAN Web-based Management Dhcp Configuration Dhcp Server Settings for the LAN DNS Server Setting Use the UT-300R2 for DhcpDisabling the Dhcp Server Configuring the LAN Connection Web-based Management Save New Settings Web-based Management Advanced Configuration / Network Management Advanced configuration menus Virtual Server Configuration NATAdvanced Configuration / Network Management Advanced Configuration / Network Management Directory Configuration and Read-only Menus Special Application Configuration Directory Configuration and Read-only Menus This is the TCP or UDP port number that will be used Configure a Filter Rule-IP Filters Advanced Configuration / Network Management Advanced Configuration / Network Management MAC Select Allow to permit packets to pass through Configuring a Filter Rule- MAC Filters Advanced Configuration / Network Management Directory Configuration and Read-only Menus Configuring a Filter Rule-URL Blocking Advanced Configuration / Network Management Directory Configuration and Read-only Menus Configuring a Filter Rule-Domain Blocking Advanced Configuration / Network Management This radio button selects the URL filter rule Firewall Configuration Menu FirewallAttacks Port Scans DMZ Ddns RIP Administrator’s Settings ToolsConfigure System Time Administrator Settings MenuSave UT-300R2 Configuration Settings Save Configuration File to PC Load Saved Configuration Files System SettingsRestore Factory Default Settings Firmware UpdateTools UT-300R2 Status Information LogTraffic Statistics Traffic StatisticsDiagnostics DiagnosticsTechnical Specifications AttachmentsSafety and Environmental Tftp Glossary Attachments