UTStarcom UT-300R2 manual Advanced Configuration / Network Management

Page 52

50 Chapter 5 Advanced Configuration / Network Management

additional IP filter rule and click the Apply button, the new rule will be added to this list.

The first step in configuring an IP filter rule is to determine if you want to Allow or Deny access. Click the appropriate radio button under the Action field. You can also turn the IP filter rule on or off using the Enabled or Disabled radio buttons under the Status field. For easy reference, you can enter an alphanumeric name in the Name field.

You can then specify the Source for packets to be filtered from the drop-down menu. If the source is selected as LAN, then this rule will apply to packets that are sent from PCs on your LAN to the WAN (Internet). If the source is selected as WAN, then this rule will apply to packets that are sent from PCs on the WAN. If both are selected, then this rule will apply to packets that are sent from PCs on both the WAN and your LAN.

A similar situation applies to the Destination drop-down menu. If the destination is selected as LAN, then this rule will apply to packets that are to be sent to PCs on your LAN. If the destination is selected as WAN, this rule will apply to packets that are to be sent to PCs on the WAN. If Both is selected, then this rule will apply to packets that are to be sent to PCs on both the WAN and your LAN.

Next, you must enter either a single IP address or a range of IP addresses in the IP Range Start and IP Range End fields. Remember that IP addresses are in the form x.x.x.x where x varies from 0 to 255 and that an IP address range must be contiguous.

Image 52
Contents UT-300R2 ADSL2/2+Modem United States Government Legends Contents UT-300R2 Status Information Attachments Overview Device IntroductionFeatures Device AppearanceOverview Installation Planning Packing ListInterfaces Introduction Front PanelCable Connections Connecting the Adsl LineRear Panel Connecting the UT-300R2 to the Ethernet LAN Hub or Switch to UT-300R2 Connection Computer to UT-300R2 ConnectionPower on Installation Planning Before Configuring UT-300R2 Set up TCP/IP on Your PCSet up Proxy Service Configure IP Settings on Your PCFirst Time Log on Web-based Management SummaryWeb-based Management Configuring the WAN Connection Options of Web-basedWeb-based Management Configuring a Bridged Connection for the WAN WAN Setting − Add menuDepending on which WAN Type and Connection Type you select Web-based Management Configuring a Routed/Bridged Connection for the WAN WAN Settings Menu Routed/Bridged Mode Configuring a PPP Connection for the WAN Web-based Management Dynamic IP Address for the WAN Connection Web-based Management Static IP Address for WAN Web-based Management Dhcp Configuration Dhcp Server Settings for the LAN Use the UT-300R2 for Dhcp DNS Server SettingDisabling the Dhcp Server Configuring the LAN Connection Web-based Management Save New Settings Web-based Management Advanced Configuration / Network Management Advanced configuration menus Virtual Server Configuration NATAdvanced Configuration / Network Management Advanced Configuration / Network Management Directory Configuration and Read-only Menus Special Application Configuration Directory Configuration and Read-only Menus This is the TCP or UDP port number that will be used Configure a Filter Rule-IP Filters Advanced Configuration / Network Management Advanced Configuration / Network Management MAC Select Allow to permit packets to pass through Configuring a Filter Rule- MAC Filters Advanced Configuration / Network Management Directory Configuration and Read-only Menus Configuring a Filter Rule-URL Blocking Advanced Configuration / Network Management Directory Configuration and Read-only Menus Configuring a Filter Rule-Domain Blocking Advanced Configuration / Network Management This radio button selects the URL filter rule Firewall Configuration Menu FirewallAttacks Port Scans DMZ Ddns RIP Administrator’s Settings ToolsConfigure System Time Administrator Settings MenuSave UT-300R2 Configuration Settings Save Configuration File to PC Load Saved Configuration Files System SettingsRestore Factory Default Settings Firmware UpdateTools UT-300R2 Status Information LogTraffic Statistics Traffic StatisticsDiagnostics DiagnosticsTechnical Specifications AttachmentsSafety and Environmental Tftp Glossary Attachments