RAD Data comm IPmux-16 operation manual T1 FDL Support, T1 PRM Support

Page 83

IPmux-16Installation and Operation Manual	Chapter 4 Troubleshooting and Diagnostics

	AIS	IPmux-16


PBX
PBX
	Internal Loop

Figure 4-2. Internal Loop

T1 FDL Support

The following FDL commands are supported:

•Line Loopback (LLB): external loop

•Line Loopback Release: normal state

T1 PRM Support

The T1 module supports PRM message transmission according to the ANSI T1.403 protocol. Messages are transmitted every second.

Diagnostic Tests

4-5

Image 83

Contents International Headquarters RAD Data Communications Inc IPmux-16Regulatory Information Safety Status Ports Safety WarningsPage Contents IPmux-16 Troubleshooting and DiagnosticsPacket Delay Variation 30. T1 Physical Layer Configuration Menu List of Tables IPmux-16 with an E1 interface OverviewVersions ApplicationsSite C Site aSite B Ethernet FeaturesManagement QoS Mode of OperationMultibundling Internal Cross ConnectInternal Clock Physical DescriptionStandards GeneralSingle E1/T1 Port at Central Site Functional DescriptionFront Panel Rear PanelTiming Modes TestingOperation Modes Single Source Clock Network E1/T1 Device ConfigurationIPmux-16 Configuration External Network TimingFrame Format IPmux-16 in Adaptive Timing ModeEthernet Frame Structure LayerLayer IP Layer Layer DataUDP Source Port as Destination Voice Port Packet Delay VariationVlan Support UDP SupportIntrinsic PDV Pdvt Buffer Effect on DelayTo configure jitter buffer depth Pdvt Jitter BufferLength Ethernet ThroughputEthernet Throughput Unframed E1 Frame Overhead Packets ThroughputT1 interface = Round Trip DelayWhere n = TDM bytes/frame Ethernet Throughput Unframed T1System Usage for TDM Bytes per Frame End-to-End Alarm GenerationThroughput Limitations and CAC T1 Modules Technical SpecificationsE1 Modules Power is off Connector DB-9System Indicators General Green On when main power supply is OFF when malfunction isPower Physical Site Requirements and Prerequisites IntroductionEquipment Needed Package ContentsNull Cable Pinout Connections DB-9 Female Signal Name Pin NoGrounding Installation and SetupSetting Jumpers Connecting Interfaces and CablesTo connect the Control Port Location of ConnectorsConnecting the Control Port Connecting the Alarm ConnectorPin No Signal Name Status Connecting the PowerAlarm Connector Pinout To connect the powerIPmux-16 Front Panel LEDs Front Panel Controls, Connectors, and IndicatorsTurning IPmux-16 On Without Control Terminal IPmux-16 System Indicators and SwitchesTo power up IPmux-16 without a terminal Operating InstructionsTo enter as a superuser User Name and PasswordTo power up IPmux-16 with a control terminal Turning IPmux-16 On With Control TerminalGetting Started To set all passwords to the default valueIf a user forgets his password To power off the unitNavigating Menu OperationsIPmux-16 Terminal Menu Tree Viewing System Information Configuring System ParametersTo access the System menu Main MenuTo display IPmux-16 general information General InformationType 3 Event Log in the System Menu Event LogTo view the IPmux-16 event log To ping Configuring IPmux-16To access the Configuration menu PingBundle connections General ConfigurationManagement Configuration To display the General Configuration MenuCommunity Authentication/CommunityManagement Configuration To change the Host ID configuration To set the Authentication/Community parametersHost Configuration To configure the Host IPManager List Configure the new Host IPManager List Host IP is deletedTo set the manager list parameters Default GatewayTo configure the default gateway Type 4 Default Gateway in the Management Configuration menuIPmux-16 Alarms Alarms Trap MaskTo define the Alarms Traps Mask To activate/deactivate a trap generation for an alarmIf no characters were sent by the terminal for Ascii Terminal ConfigurationAll other Alarms are unused To configure the Ascii terminalTo perform Software Download/Upload Time/Date UpdateTime/Date Update Menu Software Download/UploadTo download or upload a file by X-Modem, do the following To download/upload the code/configurationType 2 to download/upload via Tftp ModemXXXXXXXXX.YYY To download or upload a file by TFTP, do the following23. View Transfer Status Window View Transfer StatusFile System Set Default ParametersTo set the default parameters Type 6 File System in the General Configuration menuCDB CFG LOG COD To view and configure LAN port type Physical Layer ConfigurationLAN Configuration To configure the IPmux-16 physical layerTo configure the E1/T1 interfaces E1/T1 ConfigurationE1/T1 Physical Layer Configuration E1 Physical Layer ConfigurationTo change the source of the transmit clock To change the Loopback State settingTo change the RX Sensitivity setting To change the Line Type settingType 7 Cond. data pattern and enter a new value To determine the Signaling mode CAS enable / CAS disableRange 00-FF Default Value FF Internal Local clock source used Default value Adaptive T1 Physical Layer ConfigurationTo change the Channel Mode setting To change the Channel Type settingDefault value T1-ESF To change the Channel Code settingType a Cond. data pattern and enter a new value To change the Restore Time settingTo configure the time slots Time Slots ConfigurationActive Time Slots in this Bundle To configure IPmux-16 bundlesSET To set the Connection Status Bundle Connection ConfigurationTo view and configure Bundle Connection parameters To set the source DS0 Bundle IDTo define the Jitter Buffer Internal Cross Connect SettingsTo define a Next Hop To define a destination bundle at the remote IPmux-16Vlan Tagging Setting Vlan and IP SupportSystem Usage IP ToS Viewing Configuration SummaryTo set the IP ToS Type of Service ToS configuration configures the Whole byteTo view E1/T1 or Ethernet statistics Monitoring System PerformanceTo view performance statistics Type 3 Performance Monitoring in the Main menuLCV Compliance to standardsPhysical Port Statistics LOSAlarm Failure Comments E1/T1 Alarms and StatisticsFebe Alarms and StatisticsSES Alarm Failure Comments Valid in X only37. LAN Statistics Menu LAN StatisticsDescription Bundle Connection StatusTo view Connection status Bundle Connection Status IP Channel StatusOperation Configuring IPmux-16 Front Panel LEDs Error DetectionWorking with the Alarm Buffer Event Description Corrective Action Event TypesFault Probable Cause Remedial Action TroubleshootingIPmux-16 Troubleshooting Chart To run a loopback test Diagnostic TestsExternal Loop Internal LoopT1 PRM Support T1 FDL SupportTroubleshooting and Diagnostics Diagnostic Tests General Booting IPmux-16Boot Sequence GeneralFigure A-1 Boot Screen IPMUX-16 Boot Menu Accessing the File SystemAppendix a Boot Sequence for Downloading Software Snmp Operations Snmp EnvironmentSnmp Principles MIB Structure Management Information Base MIBManagement Domains Under Snmp MIBs Supported by the IPmux-16 Snmp AgentNetwork Management Stations AuthenticationSnmp Communities To open a Telnet application Using Telnet to Manage the IPmux-16Starting a Telnet Session System Security Configuration windowConfigurations, menu line 4 15 Minute Timeout Telnet OperationTo start download Inband Tftp Download ProcedureNew software Log in as Superuser su Preliminary ProcedureBefore performing Tftp download To check the download Checking the DownloadFigure D-3. System Description Connecting the DC Plug DC Power Supply Connection CBL-DC-3WL/F