RAD Data comm IPmux-16 operation manual To download/upload the code/configuration, Modem

Page 51

IPmux-16Installation and Operation Manual	Chapter 3 Operation

➤To download/upload the code/configuration:

1.Type 1 in the Software Download/Upload menu to download/upload using

XMODEM.

2.Type 2 to download/upload via TFTP.

X-Modem

Main Menu

↓

2.Configuration

↓

1.General Configuration

↓

4.Software Download/Upload

↓

1.Download/Upload

Xmodem

Enter 1 from the Software Download/Upload window to download or upload a file by X-modem. The Download/Upload Using X-Modem window is displayed.

	Download/Upload Using XMODEM
File	application code
ESC. Exit	D. Download U. Upload


	Figure 3-21. Download/Upload Using X-Modem Window

➤To download or upload a file by X-Modem, do the following:

1.Enter 1 from the Download/Upload Using X-Modem window and enter in the file name to be downloaded or uploaded. The file options are listed. Remember that only configuration files can be uploaded. If you choose any other file, the U. Upload option is not displayed.

2.Enter D to download a software or configuration file or U to upload a configuration file (the upload option is for configuration only), as desired. You will be asked for confirmation. Upon confirmation, the download or upload procedure begins.

Configuring IPmux-16

3-19

Image 51

Contents International Headquarters RAD Data Communications Inc IPmux-16Regulatory Information Safety Status Ports Safety WarningsPage Contents Troubleshooting and Diagnostics Packet Delay VariationIPmux-16 30. T1 Physical Layer Configuration Menu List of Tables IPmux-16 with an E1 interface OverviewVersions ApplicationsSite a Site BSite C Features ManagementEthernet QoS Mode of OperationMultibundling Internal Cross ConnectInternal Clock Physical DescriptionStandards GeneralSingle E1/T1 Port at Central Site Functional DescriptionFront Panel Rear PanelTesting Operation ModesTiming Modes Single Source Clock Network E1/T1 Device ConfigurationIPmux-16 Configuration External Network TimingFrame Format IPmux-16 in Adaptive Timing ModeEthernet Frame Structure LayerLayer IP Layer Layer DataUDP Source Port as Destination Voice Port Packet Delay VariationVlan Support UDP SupportIntrinsic PDV Pdvt Buffer Effect on DelayTo configure jitter buffer depth Pdvt Jitter BufferLength Ethernet ThroughputEthernet Throughput Unframed E1 Frame Overhead Packets ThroughputT1 interface = Round Trip DelayWhere n = TDM bytes/frame Ethernet Throughput Unframed T1End-to-End Alarm Generation Throughput Limitations and CACSystem Usage for TDM Bytes per Frame Technical Specifications E1 ModulesT1 Modules Power is off Connector DB-9System Indicators General Green On when main power supply is OFF when malfunction isPower Physical Site Requirements and Prerequisites IntroductionEquipment Needed Package ContentsNull Cable Pinout Connections DB-9 Female Signal Name Pin NoGrounding Installation and SetupSetting Jumpers Connecting Interfaces and CablesTo connect the Control Port Location of ConnectorsConnecting the Control Port Connecting the Alarm ConnectorPin No Signal Name Status Connecting the PowerAlarm Connector Pinout To connect the powerIPmux-16 Front Panel LEDs Front Panel Controls, Connectors, and IndicatorsTurning IPmux-16 On Without Control Terminal IPmux-16 System Indicators and SwitchesTo power up IPmux-16 without a terminal Operating InstructionsTo enter as a superuser User Name and PasswordTo power up IPmux-16 with a control terminal Turning IPmux-16 On With Control TerminalGetting Started To set all passwords to the default valueIf a user forgets his password To power off the unitNavigating Menu OperationsIPmux-16 Terminal Menu Tree Viewing System Information Configuring System ParametersTo access the System menu Main MenuTo display IPmux-16 general information General InformationEvent Log To view the IPmux-16 event logType 3 Event Log in the System Menu To ping Configuring IPmux-16To access the Configuration menu PingBundle connections General ConfigurationManagement Configuration To display the General Configuration MenuAuthentication/Community Management ConfigurationCommunity To change the Host ID configuration To set the Authentication/Community parametersHost Configuration To configure the Host IPManager List Configure the new Host IPManager List Host IP is deletedTo set the manager list parameters Default GatewayTo configure the default gateway Type 4 Default Gateway in the Management Configuration menuIPmux-16 Alarms Alarms Trap MaskTo define the Alarms Traps Mask To activate/deactivate a trap generation for an alarmIf no characters were sent by the terminal for Ascii Terminal ConfigurationAll other Alarms are unused To configure the Ascii terminalTo perform Software Download/Upload Time/Date UpdateTime/Date Update Menu Software Download/UploadTo download or upload a file by X-Modem, do the following To download/upload the code/configurationType 2 to download/upload via Tftp ModemXXXXXXXXX.YYY To download or upload a file by TFTP, do the following23. View Transfer Status Window View Transfer StatusFile System Set Default ParametersTo set the default parameters Type 6 File System in the General Configuration menuCDB CFG LOG COD To view and configure LAN port type Physical Layer ConfigurationLAN Configuration To configure the IPmux-16 physical layerTo configure the E1/T1 interfaces E1/T1 ConfigurationE1/T1 Physical Layer Configuration E1 Physical Layer ConfigurationTo change the source of the transmit clock To change the Loopback State settingTo change the RX Sensitivity setting To change the Line Type settingTo determine the Signaling mode CAS enable / CAS disable Range 00-FF Default Value FFType 7 Cond. data pattern and enter a new value Internal Local clock source used Default value Adaptive T1 Physical Layer ConfigurationTo change the Channel Mode setting To change the Channel Type settingDefault value T1-ESF To change the Channel Code settingType a Cond. data pattern and enter a new value To change the Restore Time settingTo configure the time slots Time Slots ConfigurationTo configure IPmux-16 bundles SETActive Time Slots in this Bundle To set the Connection Status Bundle Connection ConfigurationTo view and configure Bundle Connection parameters To set the source DS0 Bundle IDTo define the Jitter Buffer Internal Cross Connect SettingsTo define a Next Hop To define a destination bundle at the remote IPmux-16Setting Vlan and IP Support System UsageVlan Tagging IP ToS Viewing Configuration SummaryTo set the IP ToS Type of Service ToS configuration configures the Whole byteTo view E1/T1 or Ethernet statistics Monitoring System PerformanceTo view performance statistics Type 3 Performance Monitoring in the Main menuLCV Compliance to standardsPhysical Port Statistics LOSAlarm Failure Comments E1/T1 Alarms and StatisticsFebe Alarms and StatisticsSES Alarm Failure Comments Valid in X only37. LAN Statistics Menu LAN StatisticsBundle Connection Status To view Connection statusDescription Bundle Connection Status IP Channel StatusOperation Configuring IPmux-16 Error Detection Working with the Alarm BufferFront Panel LEDs Event Description Corrective Action Event TypesTroubleshooting IPmux-16 Troubleshooting ChartFault Probable Cause Remedial Action To run a loopback test Diagnostic TestsExternal Loop Internal LoopT1 PRM Support T1 FDL SupportTroubleshooting and Diagnostics Diagnostic Tests General Booting IPmux-16Boot Sequence GeneralFigure A-1 Boot Screen IPMUX-16 Boot Menu Accessing the File SystemAppendix a Boot Sequence for Downloading Software Snmp Environment Snmp PrinciplesSnmp Operations MIB Structure Management Information Base MIBManagement Domains Under Snmp MIBs Supported by the IPmux-16 Snmp AgentAuthentication Snmp CommunitiesNetwork Management Stations Using Telnet to Manage the IPmux-16 Starting a Telnet SessionTo open a Telnet application System Security Configuration windowConfigurations, menu line 4 15 Minute Timeout Telnet OperationInband Tftp Download Procedure New softwareTo start download Preliminary Procedure Before performing Tftp downloadLog in as Superuser su To check the download Checking the DownloadFigure D-3. System Description Connecting the DC Plug DC Power Supply Connection CBL-DC-3WL/F