RAD Data comm IPmux-16 operation manual Figure D-3. System Description

Page 98

Appendix D TFTP Download Procedures	IPmux-16Installation and Operation Manual

Figure D-3. System Description

D-4 Inband TFTP Download Procedure

Image 98

Contents IPmux-16 International Headquarters RAD Data Communications IncRegulatory Information Safety Warnings Safety Status PortsPage Contents IPmux-16 Troubleshooting and DiagnosticsPacket Delay Variation 30. T1 Physical Layer Configuration Menu List of Tables Applications OverviewVersions IPmux-16 with an E1 interfaceSite C Site aSite B Ethernet FeaturesManagement Internal Cross Connect Mode of OperationMultibundling QoSGeneral Physical DescriptionStandards Internal ClockRear Panel Functional DescriptionFront Panel Single E1/T1 Port at Central SiteTiming Modes TestingOperation Modes External Network Timing E1/T1 Device ConfigurationIPmux-16 Configuration Single Source Clock NetworkIPmux-16 in Adaptive Timing Mode Frame FormatLayer Data LayerLayer IP Layer Ethernet Frame StructureUDP Support Packet Delay VariationVlan Support UDP Source Port as Destination Voice PortPdvt Jitter Buffer Pdvt Buffer Effect on DelayTo configure jitter buffer depth Intrinsic PDVFrame Overhead Packets Throughput Ethernet ThroughputEthernet Throughput Unframed E1 LengthEthernet Throughput Unframed T1 Round Trip DelayWhere n = TDM bytes/frame T1 interface =System Usage for TDM Bytes per Frame End-to-End Alarm GenerationThroughput Limitations and CAC T1 Modules Technical SpecificationsE1 Modules Green On when main power supply is OFF when malfunction is Connector DB-9System Indicators General Power is offPower Physical Introduction Site Requirements and PrerequisitesPackage Contents Equipment NeededDB-9 Female Signal Name Pin No Null Cable Pinout ConnectionsConnecting Interfaces and Cables Installation and SetupSetting Jumpers GroundingConnecting the Alarm Connector Location of ConnectorsConnecting the Control Port To connect the Control PortTo connect the power Connecting the PowerAlarm Connector Pinout Pin No Signal Name StatusFront Panel Controls, Connectors, and Indicators IPmux-16 Front Panel LEDsOperating Instructions IPmux-16 System Indicators and SwitchesTo power up IPmux-16 without a terminal Turning IPmux-16 On Without Control TerminalTurning IPmux-16 On With Control Terminal User Name and PasswordTo power up IPmux-16 with a control terminal To enter as a superuserTo power off the unit To set all passwords to the default valueIf a user forgets his password Getting StartedMenu Operations NavigatingIPmux-16 Terminal Menu Tree Main Menu Configuring System ParametersTo access the System menu Viewing System InformationGeneral Information To display IPmux-16 general informationType 3 Event Log in the System Menu Event LogTo view the IPmux-16 event log Ping Configuring IPmux-16To access the Configuration menu To pingTo display the General Configuration Menu General ConfigurationManagement Configuration Bundle connectionsCommunity Authentication/CommunityManagement Configuration To configure the Host IP To set the Authentication/Community parametersHost Configuration To change the Host ID configurationHost IP is deleted Configure the new Host IPManager List Manager ListType 4 Default Gateway in the Management Configuration menu Default GatewayTo configure the default gateway To set the manager list parametersTo activate/deactivate a trap generation for an alarm Alarms Trap MaskTo define the Alarms Traps Mask IPmux-16 AlarmsTo configure the Ascii terminal Ascii Terminal ConfigurationAll other Alarms are unused If no characters were sent by the terminal forSoftware Download/Upload Time/Date UpdateTime/Date Update Menu To perform Software Download/UploadModem To download/upload the code/configurationType 2 to download/upload via Tftp To download or upload a file by X-Modem, do the followingTo download or upload a file by TFTP, do the following XXXXXXXXX.YYYView Transfer Status 23. View Transfer Status WindowType 6 File System in the General Configuration menu Set Default ParametersTo set the default parameters File SystemCDB CFG LOG COD To configure the IPmux-16 physical layer Physical Layer ConfigurationLAN Configuration To view and configure LAN port typeE1/T1 Configuration To configure the E1/T1 interfacesE1 Physical Layer Configuration E1/T1 Physical Layer ConfigurationTo change the Line Type setting To change the Loopback State settingTo change the RX Sensitivity setting To change the source of the transmit clockType 7 Cond. data pattern and enter a new value To determine the Signaling mode CAS enable / CAS disableRange 00-FF Default Value FF T1 Physical Layer Configuration Internal Local clock source used Default value AdaptiveTo change the Channel Code setting To change the Channel Type settingDefault value T1-ESF To change the Channel Mode settingTo change the Restore Time setting Type a Cond. data pattern and enter a new valueTime Slots Configuration To configure the time slotsActive Time Slots in this Bundle To configure IPmux-16 bundlesSET To set the source DS0 Bundle ID Bundle Connection ConfigurationTo view and configure Bundle Connection parameters To set the Connection StatusTo define a destination bundle at the remote IPmux-16 Internal Cross Connect SettingsTo define a Next Hop To define the Jitter BufferVlan Tagging Setting Vlan and IP SupportSystem Usage ToS configuration configures the Whole byte Viewing Configuration SummaryTo set the IP ToS Type of Service IP ToSType 3 Performance Monitoring in the Main menu Monitoring System PerformanceTo view performance statistics To view E1/T1 or Ethernet statisticsLOS Compliance to standardsPhysical Port Statistics LCVE1/T1 Alarms and Statistics Alarm Failure CommentsAlarms and Statistics FebeAlarm Failure Comments Valid in X only SESLAN Statistics 37. LAN Statistics MenuDescription Bundle Connection StatusTo view Connection status IP Channel Status Bundle Connection StatusOperation Configuring IPmux-16 Front Panel LEDs Error DetectionWorking with the Alarm Buffer Event Types Event Description Corrective ActionFault Probable Cause Remedial Action TroubleshootingIPmux-16 Troubleshooting Chart Internal Loop Diagnostic TestsExternal Loop To run a loopback testT1 FDL Support T1 PRM SupportTroubleshooting and Diagnostics Diagnostic Tests General Booting IPmux-16Boot Sequence GeneralFigure A-1 Boot Screen Accessing the File System IPMUX-16 Boot MenuAppendix a Boot Sequence for Downloading Software Snmp Operations Snmp EnvironmentSnmp Principles Management Information Base MIB MIB StructureMIBs Supported by the IPmux-16 Snmp Agent Management Domains Under SnmpNetwork Management Stations AuthenticationSnmp Communities To open a Telnet application Using Telnet to Manage the IPmux-16Starting a Telnet Session Telnet Operation Configuration windowConfigurations, menu line 4 15 Minute Timeout System SecurityTo start download Inband Tftp Download ProcedureNew software Log in as Superuser su Preliminary ProcedureBefore performing Tftp download Checking the Download To check the downloadFigure D-3. System Description DC Power Supply Connection CBL-DC-3WL/F Connecting the DC Plug