RAD Data comm IPmux-16 operation manual Appendix a Boot Sequence for Downloading Software

Page 88

Appendix A Boot Sequence for Downloading Software	IPmux-16Installation and Operation Manual

•Delete the operating file; the backup file becomes the operating file.

•Delete the configuration file.

•Delete all the software and configuration files.

If you choose to exchange or delete a file, a prompt asking for confirmation is displayed.

A-4 Booting IPmux-16

Image 88

Contents IPmux-16 International Headquarters RAD Data Communications IncRegulatory Information Safety Warnings Safety Status PortsPage Contents Packet Delay Variation Troubleshooting and DiagnosticsIPmux-16 30. T1 Physical Layer Configuration Menu List of Tables Overview VersionsApplications IPmux-16 with an E1 interfaceSite B Site aSite C Management FeaturesEthernet Mode of Operation MultibundlingInternal Cross Connect QoSPhysical Description StandardsGeneral Internal ClockFunctional Description Front PanelRear Panel Single E1/T1 Port at Central SiteOperation Modes TestingTiming Modes E1/T1 Device Configuration IPmux-16 ConfigurationExternal Network Timing Single Source Clock NetworkIPmux-16 in Adaptive Timing Mode Frame FormatLayer Layer IP LayerLayer Data Ethernet Frame StructurePacket Delay Variation Vlan SupportUDP Support UDP Source Port as Destination Voice PortPdvt Buffer Effect on Delay To configure jitter buffer depthPdvt Jitter Buffer Intrinsic PDVEthernet Throughput Ethernet Throughput Unframed E1Frame Overhead Packets Throughput LengthRound Trip Delay Where n = TDM bytes/frameEthernet Throughput Unframed T1 T1 interface =Throughput Limitations and CAC End-to-End Alarm GenerationSystem Usage for TDM Bytes per Frame E1 Modules Technical SpecificationsT1 Modules Connector DB-9 System Indicators GeneralGreen On when main power supply is OFF when malfunction is Power is offPower Physical Introduction Site Requirements and PrerequisitesPackage Contents Equipment NeededDB-9 Female Signal Name Pin No Null Cable Pinout ConnectionsInstallation and Setup Setting JumpersConnecting Interfaces and Cables GroundingLocation of Connectors Connecting the Control PortConnecting the Alarm Connector To connect the Control PortConnecting the Power Alarm Connector PinoutTo connect the power Pin No Signal Name StatusFront Panel Controls, Connectors, and Indicators IPmux-16 Front Panel LEDsIPmux-16 System Indicators and Switches To power up IPmux-16 without a terminalOperating Instructions Turning IPmux-16 On Without Control TerminalUser Name and Password To power up IPmux-16 with a control terminalTurning IPmux-16 On With Control Terminal To enter as a superuserTo set all passwords to the default value If a user forgets his passwordTo power off the unit Getting StartedMenu Operations NavigatingIPmux-16 Terminal Menu Tree Configuring System Parameters To access the System menuMain Menu Viewing System InformationGeneral Information To display IPmux-16 general informationTo view the IPmux-16 event log Event LogType 3 Event Log in the System Menu Configuring IPmux-16 To access the Configuration menuPing To pingGeneral Configuration Management ConfigurationTo display the General Configuration Menu Bundle connectionsManagement Configuration Authentication/CommunityCommunity To set the Authentication/Community parameters Host ConfigurationTo configure the Host IP To change the Host ID configurationConfigure the new Host IP Manager ListHost IP is deleted Manager ListDefault Gateway To configure the default gatewayType 4 Default Gateway in the Management Configuration menu To set the manager list parametersAlarms Trap Mask To define the Alarms Traps MaskTo activate/deactivate a trap generation for an alarm IPmux-16 AlarmsAscii Terminal Configuration All other Alarms are unusedTo configure the Ascii terminal If no characters were sent by the terminal forTime/Date Update Time/Date Update MenuSoftware Download/Upload To perform Software Download/UploadTo download/upload the code/configuration Type 2 to download/upload via TftpModem To download or upload a file by X-Modem, do the followingTo download or upload a file by TFTP, do the following XXXXXXXXX.YYYView Transfer Status 23. View Transfer Status WindowSet Default Parameters To set the default parametersType 6 File System in the General Configuration menu File SystemCDB CFG LOG COD Physical Layer Configuration LAN ConfigurationTo configure the IPmux-16 physical layer To view and configure LAN port typeE1/T1 Configuration To configure the E1/T1 interfacesE1 Physical Layer Configuration E1/T1 Physical Layer ConfigurationTo change the Loopback State setting To change the RX Sensitivity settingTo change the Line Type setting To change the source of the transmit clockRange 00-FF Default Value FF To determine the Signaling mode CAS enable / CAS disableType 7 Cond. data pattern and enter a new value T1 Physical Layer Configuration Internal Local clock source used Default value AdaptiveTo change the Channel Type setting Default value T1-ESFTo change the Channel Code setting To change the Channel Mode settingTo change the Restore Time setting Type a Cond. data pattern and enter a new valueTime Slots Configuration To configure the time slotsSET To configure IPmux-16 bundlesActive Time Slots in this Bundle Bundle Connection Configuration To view and configure Bundle Connection parametersTo set the source DS0 Bundle ID To set the Connection StatusInternal Cross Connect Settings To define a Next HopTo define a destination bundle at the remote IPmux-16 To define the Jitter BufferSystem Usage Setting Vlan and IP SupportVlan Tagging Viewing Configuration Summary To set the IP ToS Type of ServiceToS configuration configures the Whole byte IP ToSMonitoring System Performance To view performance statisticsType 3 Performance Monitoring in the Main menu To view E1/T1 or Ethernet statisticsCompliance to standards Physical Port StatisticsLOS LCVE1/T1 Alarms and Statistics Alarm Failure CommentsAlarms and Statistics FebeAlarm Failure Comments Valid in X only SESLAN Statistics 37. LAN Statistics MenuTo view Connection status Bundle Connection StatusDescription IP Channel Status Bundle Connection StatusOperation Configuring IPmux-16 Working with the Alarm Buffer Error DetectionFront Panel LEDs Event Types Event Description Corrective ActionIPmux-16 Troubleshooting Chart TroubleshootingFault Probable Cause Remedial Action Diagnostic Tests External LoopInternal Loop To run a loopback testT1 FDL Support T1 PRM SupportTroubleshooting and Diagnostics Diagnostic Tests Booting IPmux-16 Boot SequenceGeneral GeneralFigure A-1 Boot Screen Accessing the File System IPMUX-16 Boot MenuAppendix a Boot Sequence for Downloading Software Snmp Principles Snmp EnvironmentSnmp Operations Management Information Base MIB MIB StructureMIBs Supported by the IPmux-16 Snmp Agent Management Domains Under SnmpSnmp Communities AuthenticationNetwork Management Stations Starting a Telnet Session Using Telnet to Manage the IPmux-16To open a Telnet application Configuration window Configurations, menu line 4 15 Minute TimeoutTelnet Operation System SecurityNew software Inband Tftp Download ProcedureTo start download Before performing Tftp download Preliminary ProcedureLog in as Superuser su Checking the Download To check the downloadFigure D-3. System Description DC Power Supply Connection CBL-DC-3WL/F Connecting the DC Plug

Appendix A Boot Sequence for Downloading Software