GBC 930-028 manual 60+ Operation and Maintenance Manual

Page 2

F-60+ Operation and Maintenance Manual

The information in this publication is provided for reference and is believed to be accurate and complete. GBC Pro-Tech is not liable for errors in this publication or for incidental or consequential damage in connection with the furnishing or use of the information in this publication, including, but not limited to, any implied warranty of fitness or merchantabil- ity for any particular use.

GBC Pro-Tech reserves the right to make changes to this publication and to the products described in it without notice. All specifications and information concerning products are subject to change without notice.

Reference in this publication to information or products protected by copyright or patent does not convey any license under the rights of GBC Pro-Tech or others. GBC Pro-Tech assumes no liability arising from infringements of patents or any other rights of third par- ties.

This manual is copyrighted ©1999 by GBC Pro-Tech. All rights reserved. The information contained in this manual is proprietary and may not be reproduced, stored, transmitted, or transferred, in whole or in part, in any form without the prior and express written permis- sion of GBC Pro-Tech.

ii

© GBC Pro-Tech 1999 April

Image 2
Contents 0DLQWHQDQFH0DQXDO 60+ Operation and Maintenance Manual 6HFWLRQ Two-Pass Mount and Laminate Hot and Cold Push either Twist pressed Safety DXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV Inside cabinet Decal Meaning Blank 60+ Laminator is properly and securely unpacked Moved and installedThese instructions so that you can insure that your new Is there ample room for the laminator?Installation Alternative Power Configurations Tools required To uncrate the laminatorFork Lift Blade Locations Hex wrench Adjustable wrench Setup ProcedureStartup Checklist To level the laminatorInstallation Operation Power ON/OFF Indicator Indicates Roll Pressure Display Displays the perHE8S Covered under our warranty To your machine and is not recommended orMust be raised to prevent damaging the rolls When the machine is not in use, the pull rollsPull roll clutch tension adjustment See process chart 3URFHVV &RQWURO&KDUWVFeed the work into the nip with the leading edge tight Lay the print on the board. Using a tack iron, tackHeat-activated laminating using mounting board with Entering the nip evenly from side to side. For thin3URFHGXUH3DVV 352&66&21752/,$*5$0 Identification Diagram352&66&21752/&+$57 One Pass Mounting 352&66&21752/&+$57352&66&21752/,$*5$0 One Pass Mount and Laminate 352&66&21752/&+$57352&66&21752/,$*5$0 Process One Pass Mount & Laminate DateEncapsulation 352&66&21752/&+$57352&66&21752/,$*5$0 Product 3 Mil Gloss/3Mil GlossCold Overlamination 352&66&21752/&+$57352&66&21752/,$*5$0 Process Cold Overlamination DateCold Mount and Laminate First Pass 352&66&21752/&+$57$352&66&21752/,$*5$0$ Process Cold Mount & Laminate First Pass DateCold Mount and Laminate Second Pass 352&66&21752/&+$57%352&66&21752/,$*5$0% Product Process Cold Mount & Laminate Second PassMount and Hot Overlaminate First Pass 352&66&21752/&+$57$352&66&21752/,$*5$0$ ProductMount and Hot Overlaminate Second Pass 352&66&21752/&+$57%352&66&21752/,$*5$0% Product Process Mount & Hot Overlaminate Second PassOperation GBC Pro-Tech laminators require minimal mainte Clean the rollsAge Inspect the footswitch cord for dam Adjust the nip Adhesive coated boardTo clean beads of adhesive, dust and dirt from the rolls To clean the cabinet and covers$GMXVWLQJWKH1LS Hex wrench ¾ hex wrenchTo adjust the chain tension Hex wrench ScrewdriverXeulfdwlrq 1844 202 440 or fax +44 0 1844 2022XWSXW7URXEOHVKRRWLQJ*XLGH Faces This warranty specifically does not coverUnauthorized customer alterations will void this Warranty Customer’s sole and exclusive remedy under thisWarranty Quantity Part DescriptionSpecifications Pull roll 5clutch adjustment Grease fittings Accessory pack Laminating rolls Adjusting Laminating speedsProcess control charts Resetting the laminator 1-1,3-1Index