GBC 930-028 manual This warranty specifically does not cover, Faces, Improper use of the machine

Page 43

/LPLWHG6HFWLRQ:DUUDQW\￿￿:DUUDQW\

This warranty specifically does not cover:

-60+ Operation and Maintenance Manual

([FOXVLRQVWRWKH:DUUDQW\

Warranty

GBC Pro-Tech Engineering Company, Inc. warrants

1.

Damage to the laminating rolls caused by knives,

 

razor blades, other sharp objects, or failure caused

the equipment sold is free from defects in material and

 

 

by adhesives.

 

workmanship for a period of ninety days (90) from the

 

 

 

 

 

date of delivery to the customer. This warranty is the

2. Damage to the machine caused by lifting, tilting,

only warranty made by GBC Pro-Tech and cannot be

 

and/or any attempt to position the machine other

modified or amended.

 

than rolling on the installed casters on even sur-

GBC Pro-Tech’s sole and exclusive liability and the

 

faces.

 

 

 

 

customer’s sole and exclusive remedy under this

3.

Improper use of the machine.

 

warranty shall be, at GBC Pro-Tech’s option, to

 

 

 

repair or replace any such defective part or prod-

 

 

 

uct. These remedies are only available if GBC Pro-

 

 

 

Tech’s examination of the product discloses to GBC

 

 

 

Pro-Tech’s satisfaction that such defects actually

 

 

 

exist and were not caused by misuse, neglect,

 

 

 

attempt to repair, unauthorized alteration or modi-

 

 

 

fication, incorrect line voltage, contaminated air

 

 

 

supply, or by fire, accident, flood, or other hazard.

 

 

 

This warranty specifically does not cover damage to

 

 

 

the laminating rollers caused by knives, razor blades,

 

 

 

other sharp objects, failure caused by adhesives or

 

 

 

improper use of the machine. Warranty repair or

 

 

 

replacement does not extend the warranty beyond the

 

 

 

initial ninety day period from the date of delivery.

 

 

 

 

 

CAUTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unauthorized customer alterations will void this

 

 

 

 

warranty.

 

 

 

 

 

 

 

 

 

THE WARRANTY MADE HEREIN IS IN LIEU OF

 

 

 

ALL OTHER WARRANTIES, EXPRESS OR

 

 

 

IMPLIED, INCLUDING ANY WARRANTY OR

 

 

 

MERCHANTABILITY OR FITNESS FOR A PAR-

 

 

 

TICULAR PURPOSE. GBC PRO-TECH WILL NOT

 

 

 

BE LIABLE FOR PROPERTY DAMAGE OR PER-

 

 

 

SONAL INJURY (UNLESS PRIMARILY CAUSED

 

 

 

BY ITS NEGLIGENCE), LOSS OF PROFIT OR

 

 

 

OTHER INCIDENTAL OR CONSEQUENTIAL

 

 

 

DAMAGES ARISING OUT OF THE USE OR

 

 

 

INABILITY TO USE THE EQUIPMENT.

 

 

 

© GBC Pro-Tech 1999 April

5-1

Image 43
Contents 0DLQWHQDQFH0DQXDO 60+ Operation and Maintenance Manual 6HFWLRQ Two-Pass Mount and Laminate Hot and Cold Push either Twist pressed Safety DXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV Inside cabinet Decal Meaning Blank Is there ample room for the laminator? Moved and installedThese instructions so that you can insure that your new 60+ Laminator is properly and securely unpackedInstallation Alternative Power Configurations To uncrate the laminator Tools requiredFork Lift Blade Locations Setup Procedure Hex wrench Adjustable wrenchTo level the laminator Startup ChecklistInstallation Operation Roll Pressure Display Displays the per Power ON/OFF Indicator IndicatesHE8S To your machine and is not recommended or Covered under our warrantyPull roll clutch tension adjustment When the machine is not in use, the pull rollsMust be raised to prevent damaging the rolls 3URFHVV &RQWURO&KDUWV See process chartEntering the nip evenly from side to side. For thin Lay the print on the board. Using a tack iron, tackHeat-activated laminating using mounting board with Feed the work into the nip with the leading edge tight3URFHGXUH3DVV 352&66&21752/&+$57 Identification Diagram352&66&21752/,$*5$0 352&66&21752/,$*5$0 352&66&21752/&+$57One Pass Mounting Process One Pass Mount & Laminate Date 352&66&21752/&+$57352&66&21752/,$*5$0 One Pass Mount and LaminateProduct 3 Mil Gloss/3Mil Gloss 352&66&21752/&+$57352&66&21752/,$*5$0 EncapsulationProcess Cold Overlamination Date 352&66&21752/&+$57352&66&21752/,$*5$0 Cold OverlaminationProcess Cold Mount & Laminate First Pass Date 352&66&21752/&+$57$352&66&21752/,$*5$0$ Cold Mount and Laminate First PassProduct Process Cold Mount & Laminate Second Pass 352&66&21752/&+$57%352&66&21752/,$*5$0% Cold Mount and Laminate Second PassProduct 352&66&21752/&+$57$352&66&21752/,$*5$0$ Mount and Hot Overlaminate First PassProduct Process Mount & Hot Overlaminate Second Pass 352&66&21752/&+$57%352&66&21752/,$*5$0% Mount and Hot Overlaminate Second PassOperation Adhesive coated board Clean the rollsAge Inspect the footswitch cord for dam Adjust the nip GBC Pro-Tech laminators require minimal mainteTo clean the cabinet and covers To clean beads of adhesive, dust and dirt from the rollsHex wrench ¾ hex wrench $GMXVWLQJWKH1LS Hex wrench Screwdriver To adjust the chain tension1844 202 440 or fax +44 0 1844 202 Xeulfdwlrq2XWSXW7URXEOHVKRRWLQJ*XLGH Customer’s sole and exclusive remedy under this This warranty specifically does not coverUnauthorized customer alterations will void this Warranty FacesWarranty Part Description QuantitySpecifications Resetting the laminator 1-1,3-1 Accessory pack Laminating rolls Adjusting Laminating speedsProcess control charts Pull roll 5clutch adjustment Grease fittingsIndex