Sony PLM-S700E instruction manual Troubleshooting, Symptom Cause Remedy

Page 45

Troubleshooting

If you have any questions or problems not listed below, contact your Sony dealer or local authorised Sony service facility.

Symptom

Cause

Remedy

The picture does not

Connections are incorrect.

Connect the equipment correctly

appear.

 

(pages 14 to 19).

 

 

 

 

The signal is not input.

Select the correct input (page 30).

 

 

 

 

The Glasstron enters power save

Put the Glasstron on again to bring

 

mode.

the forehead near to the POWER

 

 

SAVING SENSOR (page 13).

 

 

 

 

When you connect to a notebook

Change the display mode. For

 

type PC, the display mode is set to

details, refer to the instruction

 

local display mode (LCD panel of

manual of your PC.

 

your notebook PC).

 

 

 

 

The picture is dark or

You are not wearing the Glasstron

Put on the Glasstron correctly (pages

dim.

correctly.

20 and 21).

 

 

 

 

Adjust the brightness with the

 

 

BRIGHT control (page 31).

 

 

 

 

Adjust the RGB signal

 

 

synchronization (page 38).

 

 

 

 

The inside window (where the

Clean the display unit with a soft,

 

picture is displayed) is dirty.

dry cloth.

The picture suddenly

A warning was displayed for more

disappears.

than two minutes. (The Glasstron

 

 

turned off automatically.)

 

 

 

 

 

You continued using the Glasstron

 

for six hours. (The Glasstron turns

 

 

off automatically after six hours to

 

 

prevent eye fatigue.)

 

 

 

 

 

The battery pack or batteries are

Charge the battery pack or replace with

 

dead.

new batteries (pages 40).

 

 

 

 

You put off the Glasstron while the

Put the Glasstron on again to bring

 

POWER SAVE is set to ON.

the forehead near to the POWER

 

 

SAVING SENSOR (page 13).

The picture has no sound.

Adjust the volume with the VOL

The sound is noisy.

 

control (page 31).

The volume does not

The AVLS function is on.

Set AVLS in the menu to OFF (page

become louder.

 

37).

 

The equipments are not connected

Connect the equipments correctly

 

propely.

(pages 14 to 19).

 

 

 

 

Sound volume of the connected

Adjust the volume on the computer.

 

computer is inappropriate.

 

 

 

 

The battery pack

The battery pack is not charged

Charge the battery pack fully or use a

discharges quickly.

enough.

new one (page 40).

 

The battery pack is completely dead.

 

 

 

continued

Additional Information

45-GB

Image 45
Contents Glasstron Precautions Table of Contents Glasstron is a brand-new concept in visual display Safety Instructions Health Concerns Health Concerns Instructions for Safe Fit Page About the Glasstron Power supply boxDisplay unit Personal ComputerFeatures Checking the supplied accessories Locating the parts and controls Power supply boxDisplay unit Getting StartedConnecting the PC Connecting the GlasstronConnecting other IBM compatible PCs To monitor port To audio port To PC AudioTo monitor Connecting a Macintosh PowerbookPort To PC To monitor port To audio port AdapterConnecting a Macintosh desktop models Connecting the GlasstronMacintosh Sub 15-pin To monitor Connecting the video equipment About the AUDIO/VIDEO input jack If your video equipment has an S-video jackAC power adapter Connecting the power sourceGetting StartedWearing the Glasstron Adjust the strapLoosen the back strap Put on the GlasstronAdjust the angle of the display unit Adjusting the back strapAdjust the stereo earphones Attaching the sunshadesTurning on the Glasstron Turn on the Glasstron sliding the Power switchChecking the display unit position Then press the jog dialFour corners as shown below Read the next Warning and press the jog dialCorrect Incorrect IncorrectTurning on the Glasstron Checking the screen position alignmentAlignment Press the Push Display jog dialIf the screens are aligned, press the jog dial Incorrect When no vertical lines When the horizontalGo to Setting the password on Password YES or no screen appearsEntered password Setting the passwordJog dial DialSetting the password Verify a password using the jog dial Changing the passwordDisplay jog dial Using the GlasstronNumbers in the same way OperationsUsing the Glasstron Follow the instructions on the screen Select the input signal using the PC-VIDEO switchInput the signal from the connected equipment Adjust the brightness by turning the Bright control After you finish using the GlasstronAdjust the sound volume by turning the VOL control Checking the display indicationUsing the Glasstron Screen warnings against overuse of the GlasstronAfter about 4 hours and 15 minutes of use Viewing the surrounding environment Set the Screen switch toTurn the SEE-THROUGH dial Picture becomes Area surrounding TransparentSignal compatibility Adjusting the sound and picturePC mode RGB signal Video mode video signalPower Save Adjusting the sound/pictureAdjust the setting using the jog dial Adjusting the sound and picture Press MenuPC mode Press the jog dialTurn the jog dial to set to ON, then press the jog dial Avls Auto Volume Limiter SystemAdjusting the sound and picture Adjusting the RGB signalAdjusting the video signal Resetting the adjustment to the factory preset levelLessmore Charging the battery pack Using the optional battery packAttach the battery pack to the power supply box Connect the AC power adapter to the DC in connector onRemaining battery life Fully Chargeddead Checking the remaining battery life Installation Precautions Use Unified polarity plugAdditional Information OthersOUT of Scan Range Error messagesSymptom Cause Remedy TroubleshootingTroubleshooting Specifications E, F, G IndexK, L Y, ZPage Avertissement Préparation Table des matièresRemarque sur l’affichage à cristaux liquides LCD Instructions DE Securite Informations DE Securite Complementaires Problèmes de santéProblèmes de santé Avertissement Ajustez correctement la visionneuse Instructions d’ajustageAvertissements relatifs aux appareils électroniques Unité d’affichage Propos de la visionneuse GlasstronBloc d’alimentation Ordinateur personnelCaractéristiques Vérification des accessoires fournis Unité d’affichage Localisation des composants et des commandesBloc d’alimentation PréparationRaccordement de l’ordinateur Raccordement du GlasstronRaccordement à d’autres ordinateurs compatibles IBM RemarquesRemarque sur le raccordement Raccordement à un Powerbook MacintoshRaccordement à un Macintosh modèles de bureau Vers le câble de signal RVB Sub à Vers le portRaccordement du Glasstron suite Remarques sur le raccordementRaccordement d’un appareil vidéo Sens du signal Suite page suivanteMinifiche spéciale Fiche phono Vers les sorties audio/vidéo Vers le connecteurSi votre équipement vidéo dispose d’une prise S-Vidéo Propos de la prise d’entrée AudioAudio R Masse GND Vidéo Raccordement de la source d’alimentation Desserrez la sangle arrière Port du GlasstronChaussez la visionneuse Glasstron Ajustez la sangleFixation des pare-soleil Réglage de la sangle arrièreAjustez l’angle de l’unité d’affichage Ajustez les écouteurs stéréoMise sous tension du Glasstron Commutateur PowerVérification de la position de l’unité d’affichage SélectionDe sélection DessousAppuyez sur la molette de sélection Appuyez sur la molette de sélection Push Display Vérification de l’alignement de l’écranEcran gauche Correct Ecran droitLigne horizontale En diagonale Passez à la section de Saisie du mot de passe à la ’écran de sélection OUI ou NON du mot de passe apparaîtMolette de sélection Push Display Saisie du mot de passeLa molette de sélection Avant de commencerModification du mot de passe Saisie du mot de passe suiteRemarque Ensuite appuyez sur la molette de commande Push Dial Utilisation du GlasstronMot de passe introduit Entrez le signal de l’appareil raccordé Lorsque vous raccordez un ordinateurLorsque vous raccordez un appareil vidéo Réglez le volume du son en tournant la commande VOL Ajustez la luminosité en tournant la commande BrightVérification de l’indication d’affichage Après avoir utilisé le GlasstronAu bout d’environ 2 heures et 15 minutes d’utilisation Utilisation du Glasstron suiteAu bout d’environ 4 heures et 15 minutes d’utilisation Au bout d’environ 6 heures d’utilisationVisualisation de l’entourage Tournez la molette de sélection SEE-THROUGHMettez le commutateur Screen sur on Mode vidéo signal vidéo Mode PC signal RVBRemarques sur le mode PC Réglage du son et de l’imageRéglage du son/image Réglage du son et de l’image suite Appuyez sur Menu Mode VideoAvls système de limitation automatique du volume Etat Indicateur Image’énergie Réglage du son et de l’image suite Réglage du signal RVBRéglage du signal vidéo Réinitialisation des réglages aux valeurs par défautMoinsplus Intenses intenses Utilisation de la batterie en option Installez la batterie sur le bloc d’alimentationCharge de la batterie ’alimentation. Raccordez ensuite le cordon d’alimentation àVérification de l’autonomie résiduelle de la batterie Précautions UtilisationFiche à polarité unifiée Remarque sur le transport DiversMessages d’erreur Symptôme Cause Remède DépannageDépannage suite Spécifications X, Y, Z Page Page Page Sony Corporation