Nx Networks NX series Keypad control menu M3, Selection of control place, Control place

Page 56

7

56(86)

Control keypad

7.3.3Keypad control menu (M3)

In the Keypad Controls Menu, it is possible to choose the control place, edit the frequency reference and change the direction of the motor. Enter the submenu level with the right arrow menu button.

NOTE! There are some special functions that can be performed when in the M3 menu:

Select the keypad as the active control place by keeping the

start

button

pushed down for 3 seconds when the motor is running. The keypad will become the active control place and the current frequency reference and direction will be copied to the keypad.

Select the keypad as the active control place by keeping the

stop

button

pushed down for 3 seconds when the motor is stopped. The keypad will become the active control place and the current frequency reference and direction will be copied to the keypad.

Copy the frequency reference set elsewhere (I/O, fieldbus) to the panel by

keeping the

enter

button pushed down for 3 seconds.

 

Note that Whilst in any other than M3 menu these functions will not work.

If in a different menu other than M3 menu and try to start the motor by pressing the START button when the keypad is not selected as the active control place an error message Keypad Control NOT ACTIVE will be displayed.

7.3.3.1Selection of control place

There are three different places (sources) which the frequency converter can be controlled from. For each control place, a different symbol will appear on the alphanumeric display:

Control place

Symbol

I/O terminals

I/O term

Keypad (panel)

Keypad

Fieldbus

Bus/Comm

 

Change the control place by entering the edit mode with the right arrow menu button. The options can then be browsed through with the Browser buttons. Select the desired control place with the Enter button. See the diagram on the next page.

See also 7.3.3 above.

Page 55 Page 57
Image 56
Page 55 Page 57
Contents NX series Start-up Quick Guide Contents NX USER’S Manual 486 Application Manual586 Index686 Control Keypad786 SafetySafety instructions = Dangerous voltage = General warning Earthing and earth fault protectionRunning the motor NX frequency converter EMC classification GeneralTechnical criteria 1086 Class TClass N Manufacturers declaration of conformityEU Declaration of Conformity 11861286 Receipt of shipmentType designation code Storage1386 MaintenanceWarranty Introduction Technical data1486 1586 1 NX5 Mains voltage 380-500 Power ratings1686 1786 CharacteristricsTechnical data 1886Mounting Installation1986 2086 Installation NX dimensions, IP21Installation 2186 NX dimensions, IP21 with collar, FR4 to FR62286 Installation Opening needed for the collar installation, FR4 to FR6Installation 2386 NX dimensions, IP21 with collar, FR7 and FR82486 Installation Opening needed for the collar installation, FR7/FR82586 Cooling2686 Power lossPower loss as function of switching frequency Power loss as function of switching frequency 0038…0061NX5 2786Cabling and connections Power unit2886 External RFI-filter Filter Option 2986Power connections Mains cableMotor cable Control cable3186 Cable and fuse sizesInstallation instructions 32863386 3486 Stripping lengths of motor and mains cablesNX frequency converter frames and installation of cables 35863686 NX, FR5. Protection class IP213786 NX, FR6. Protection class IP213886 10. NX, FR7. Protection class IP21Cable and motor insulation checks Cable installation and the UL standards3986 Control connections 4086Control unit NXOPTA1 4186Control cables Galvanic isolation barriersControl terminal signals 4386Digital input signal inversions 4486+24V Ground +24VJumper block AI1 mode AI2 mode 45864686 Control keypadIndications on the Keypad display Drive status indications See control keypadSee .3.4, Active Faults 4786Control place indications See control keypad Status LEDs green green red See control keypad4886 Reset Keypad push-buttonsButton descriptions SelectNavigation on the control keypad No editing 51865286 Monitoring menu M15386 Parameter menu M25486 P1 P18 Keypad control menu M3 Select the keypad as the active control place by keepingSelection of control place Control placeKeypad reference Keypad direction5886 Active faults menu M4Fault types Fault type symbol Meaning 5986Fault codes 6086Fault code Possible cause Correcting measures 6186Fault time data record 6286Fault history menu M5 63866486 System menu M66586 Functions in the System menuCode Function Min Max Unit Default Cust Selections 6686Language selection 6786Application selection System settings 6886ChangeEnable ChangeDisabl 6986Connected Not conn 7086Example Keypad settings7186 Keypad settings Default 72867386 Parameter copy7486 20. Storing and loading of parameter sets7586 Parameter comparison7686 Information submenu7786 Counters menu7886 Trip counters submenu7986 Expander board menu M7G1 G2 Auto8086 Further keypad functionsCommissioning of the frequency converter Commissioning8186 8286 8386 Fault tracing 84868586 Bulgaria
Top Page Image Contents