Initio I/O HIGHWAY manual Product Warranty, FCC Compliance Statement

Page 61

57

Product Warranty

Initio Corporation warrants to the original purchaser that this product shall be free from defects in material and workmanship for a period of 5 years from the date of purchase. Should this product, in the judgment of Initio Corporation, prove to be defective, Initio Corporation will at its option repair or replace the product once it has been returned to Initio Corporation free of charge. Any replaced parts or products become the property of Initio Corporation. You may obtain warranty service by first getting authorization from Initio Corporation then returning this product with proof of delivery date, shipping charges prepaid, to Initio Corporation. This warranty does not apply to the software component of the product nor to any product which has been subjected to misuse, accident, abuse or use in a manner inconsistent with normal host adapter operations. The original purchaser must be registered with Initio Corporation (by mailing the Product Registration Card) to qualify for warranty coverage. This remedy is your exclusive remedy for breach of this warranty.

INITIO DISCLAIMS ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MER- CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. INITIO SHALL BE LIMITED TO THE WARRANTY PERIOD SPECIFIED ABOVE. ALL OTHER WARRANTIES ARE EXCLUDED. INITIO’S TOTAL LIABILITY HEREUNDER SHALL NOT EXCEED THE PRICE PAID FOR THE PRODUCT PURCHASED. IN NO EVENT SHALL INITIO BE LIABLE FOR ANY INDI- RECT, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFOR- MANCE OF THE PRODUCT, EVEN IF INITIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.

Class B Equipment

Information to User

This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions contained in this manual, may cause harmful interference to radio commu- nications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that of the receiver.

Consult the dealer or a experienced audio television technician.

Note: Connecting this device to peripheral devices that do not comply with CLASS B requirements or using an unshielded peripheral data cable could also result in harmful interference to radio or television reception.

initio®

Image 61
Contents Initioi D119-03 May Third Edition Contents Troubleshooting Index Product Warranty Initio IntroductionHost Adapter INI-9100A Board Layout Technical IllustrationProduct Features Product Features/SpecificationsProduct Specifications Host Adapter and the Scsi Bus Getting StartedScsi bus preparation Scsi bus terminationOFF Ohighway possible termination settingsInstallation Basics Hardware InstallationInstallation in Ten Easy Steps OhighwayInserting the host adapter into a PCI slot Connecting the 50-pin internal flat ribbon cable Hardware Installation Low-level Format Hard Disk Drive PreparationInitio Running the SmartSCSI Setup Utility Host Adapter SetupDevice Setup Main Menu OptionsData can be Lost by Changing Settings Adapter SetupDisk Utilities Bios SetupInitio Installation MS-DOS/Windows 3.1x Driver InstallationOverview MS-DOS/Windows 3.1x Driver Installation Aspi CD-ROM Driver Command Line Options Aspi Manager Command Line OptionsAutoexec.bat Sample CONFIG.SYS and AUTOEXEC.BAT FilesAspi Disk Driver Command Line Options Aspi Partition & Format Utility Sample CONFIG.SYSNew Windows 95/95a Installation Microsoft Windows 95/95b OSR2 Driver InstallationControl Panel Microsoft Windows 95/95b OSR2 Driver Installation Updating the Initio Windows 95/95a Device Driver New Windows 95B OSR2 Installation Microsoft Windows 95/95b OSR2 Driver Installation Updating the Initio Windows 95B OSR2 Device Driver Initio New Windows NT Installation Microsoft Windows NT Driver InstallationMicrosoft Windows NT Driver Installation Control Panel Installing a new Windows NT system from a Bootable CD New IntraNetWare Installation Novell NetWare Driver InstallationPCI.XXXX.XXXX.XXXX.XXXX.XX Novell NetWare Driver InstallationUpgrading/Changing Driver on an Existing IntraNetWare Server Driver Config Options Device driver command line optionsNew OS/2 installation IBM OS/2 Driver InstallationAdding the Initio driver to an existing OS/2 system Device driver command line options Initio Updating interrupts and hardware settings SCO Unix Driver Installation10Overview Adding the Initio driver to an existing SCO Unix system Installing the Initio driver in a new SCO Unix systemEnter Changing to the INI-9XXX as the bootable host adapter Initio Installing the Initio driver in a new UnixWare system SCO UnixWare Driver InstallationAdding the Initio driver to an existing UnixWare system Removing the Initio driver from a UnixWare system Using Multiple Host AdaptersSCO UnixWare Driver Installation Troubleshooting MS-DOS, OS/2 & Windows NT DOS Space 1GBDrives with Multiple Operating Systems Initio Index SETUP.EXE SYSTEM.INI TXTSETUP.OEM OEMSETUP.INFUpdate Driver Windows NT Workstation SetupFCC Compliance Statement Product WarrantyEN 55 9100UW2 Declaration of Conformance Declaration of the Manufacturer/Importer