Initio I/O HIGHWAY manual Adding the Initio driver to an existing UnixWare system, Enter

Page 52

48

SCO UnixWare Driver Installation

2When prompted to INSTALL HOST BUS ADAPTER DRIVERS, insert the INI-9XXXU/ 9XXXUW DRIVER DISK 2 into drive A: press <Enter>.

3When prompted to INSTALL ANOTHER HBA DISKETTE, press <ENTER> to con- tinue.

4Follow the directions on screen until you come to a window titled: Loading Initio INI- 9XXX Host Adapter.

Select CONTINUE INSTALLATION.

Select CONTINUE INSTALLATION again.

5This completes loading the host adapter driver. Follow the on-screen directions to complete the SCO UnixWare installation. For further information regarding UnixWare installation, refer to the SCO UnixWare Installation Handbook.

Adding the Initio driver to an existing UnixWare system

1Once a UnixWare session is established and a command prompt is ready, type (recall that UnixWare is case sensitive):

cp /stand/unix /stand/unix.org , press <ENTER>

pkgadd -d diskette1 , press <ENTER>

2Select i910u ihv hba from the list of available host drivers, press <ENTER>.

3If the INI-9XXX is intended to be the bootable host adapter, the next step to updating the driver will require a revision to the I910u file. These instructions will guide you through changing the current software settings for UnixWare to establish the INI-9XXX as the host adapter for your boot device:

At the system command prompt, type

cd /etc/conf/sdevice.d

Use “vi” or another editor to modify the file I910u by adding a line

locate the line $version2

edit the file by adding the line $static immediately following $version2.

Rebuild the UnixWare kernel by completing the following steps at the command prompt :

/etc/conf/bin/idbuild -B <ENTER>

cp /etc/conf/cf.d/unix /stand/unix <ENTER>

cd / <ENTER>

shutdown -g0 ( 0 is Zero ) <ENTER>

Y <ENTER>

initio®

Image 52
Contents Initioi D119-03 May Third Edition Contents Troubleshooting Index Product Warranty Initio IntroductionHost Adapter Technical Illustration INI-9100A Board LayoutProduct Features/Specifications Product FeaturesProduct Specifications Getting Started Host Adapter and the Scsi BusScsi bus preparation Scsi bus terminationOhighway possible termination settings OFFHardware Installation Installation BasicsInstallation in Ten Easy Steps OhighwayInserting the host adapter into a PCI slot Connecting the 50-pin internal flat ribbon cable Hardware Installation Hard Disk Drive Preparation Low-level FormatInitio Host Adapter Setup Running the SmartSCSI Setup UtilityDevice Setup Main Menu OptionsAdapter Setup Data can be Lost by Changing SettingsBios Setup Disk UtilitiesInitio Installation MS-DOS/Windows 3.1x Driver InstallationOverview MS-DOS/Windows 3.1x Driver Installation Aspi Manager Command Line Options Aspi CD-ROM Driver Command Line OptionsSample CONFIG.SYS and AUTOEXEC.BAT Files Autoexec.batAspi Disk Driver Command Line Options Sample CONFIG.SYS Aspi Partition & Format UtilityMicrosoft Windows 95/95b OSR2 Driver Installation New Windows 95/95a InstallationControl Panel Microsoft Windows 95/95b OSR2 Driver Installation Updating the Initio Windows 95/95a Device Driver New Windows 95B OSR2 Installation Microsoft Windows 95/95b OSR2 Driver Installation Updating the Initio Windows 95B OSR2 Device Driver Initio Microsoft Windows NT Driver Installation New Windows NT InstallationMicrosoft Windows NT Driver Installation Control Panel Installing a new Windows NT system from a Bootable CD Novell NetWare Driver Installation New IntraNetWare InstallationNovell NetWare Driver Installation PCI.XXXX.XXXX.XXXX.XXXX.XXUpgrading/Changing Driver on an Existing IntraNetWare Server Device driver command line options Driver Config OptionsIBM OS/2 Driver Installation New OS/2 installationAdding the Initio driver to an existing OS/2 system Device driver command line options Initio Updating interrupts and hardware settings SCO Unix Driver Installation10Overview Adding the Initio driver to an existing SCO Unix system Installing the Initio driver in a new SCO Unix systemEnter Changing to the INI-9XXX as the bootable host adapter Initio SCO UnixWare Driver Installation Installing the Initio driver in a new UnixWare systemAdding the Initio driver to an existing UnixWare system Using Multiple Host Adapters Removing the Initio driver from a UnixWare systemSCO UnixWare Driver Installation Troubleshooting DOS Space 1GB MS-DOS, OS/2 & Windows NTDrives with Multiple Operating Systems Initio Index OEMSETUP.INF SETUP.EXE SYSTEM.INI TXTSETUP.OEMUpdate Driver Windows NT Workstation SetupProduct Warranty FCC Compliance StatementDeclaration of the Manufacturer/Importer EN 55 9100UW2 Declaration of Conformance