Hand Held Products 5700 Dual Interface Enable/Disable Selection, Switched Power Mode Selections

Page 24

Dual Interface Enable/Disable Selection

Dual Interface Disable Selection lets you temporarily disable the dual interface selection, while retaining your secondary interface setup in memory. If you want to enable the secondary interface again, scan the Enable Dual Interface bar code below.

Enable

✱ Disable

Switched Power Mode Selections

When this feature is enabled, the unit consumes less than 50 uA from its power line when the trigger is not pulled. When the trigger is pulled, it consumes normal power. This feature is used for battery powered devices to save power. If power savings is not an issue and speed is, disable this feature for better performance.

✱ Switched Power (Low Power) Mode

Constant Power Mode

Laser Emulation Power Up Delay Selection

Scan the Laser Emulation Power Up Delay bar code to delay full power up. This allows the PDT terminal to power up on scanner trigger. The PDT powers down between scans, greatly extending battery life.

Scan two of the Numeric Bar Codes on the Programming Chart (inside back cover) to set the delay to any value between 00 and 99. 00–99 is the multiplier (x5ms).

Power Up Delay

1–16	SCANTEAM 5700 User’s Guide

Image 24

Contents Decoded Output Disclaimer Scanteam 5700 User’s Guide FCC Class B Compliance StatementCanadian Notice A. StatementPatents Table of Contents Protocol Selection Serial Wedge Output Selection Require Data Format Data Format EditorMarker Beam Selection AutoTrigger Selection Foreign Keyboard SelectionIndustrial Symbology Selections Keyboard Function Relationships Supported Interface KeysMaintenance Troubleshooting Obtaining Factory Service Technical SupportIntroduction Model Number 5X00/A-12 Scanner IdentificationConnecting the Scanner Cable, Keyboard, and Terminal will varyScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC AT and Compatibles Interface Default IBM PC, Wand Emulation InterfaceIBM PS/2 and Compatibles Interface IBM PC XT and Compatibles InterfaceIBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Instructions Dual Interface Programming NotesCode 39 Wand Emulation Selection Same Code Wand Emulation SelectionRS-232 Selection Laser Emulation SelectionDual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Prefix Selection Secondary Interface Suffix SelectionExample 1 Add Suffix for Specific Symbology Example 2 Add Suffix for ALL SymbologiesPrefix and Suffix Examples Example 4 To Clear a Specific Prefix EntrySymbology Code Hex ValueBeeper Volume Selection Output Delays SelectionReread Delay Selection Good Read Delay SelectionLaser Voting Selection Buffered Scans Selection Code I.D. Transmit SelectionAIM I.D. Transmit Selection Function Code Transmit SelectionCTS Check Selection Baud Rate SelectionRS-232 Word Length Selection Parity SelectionProtocol Selection Serial Wedge Output Selection➎ Editor Command Sequences ➋ Terminal Type➌ Code I.D ➍ LengthRequire Data Format Data Format EditorSend Commands Move CommandsSearch Commands Miscellaneous CommandsData Formatter Example UPC a with 5 digit addendaScanteam 5700 User’s Guide Introduction Marker Beam Selection AutoTrigger SelectionTransmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection AT Direct Connect Selection NCR 7052 Keypad SelectionKeyboard Style Selections Keyboard StyleKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Codabar Selection Message LengthCheck Character Code 39 Selection AppendMinimum Maximum Full Ascii Chart Code 93 SelectionInterleaved 2 of 5 Selection Check DigitCode 2 of 5 Selection Matrix 2 of 5 SelectionCode 11 Selection Code 128 SelectionCode 128 Function Character Selection Code 16K Selection Code 49 SelectionEAN Selection IsbnUPC Selection UPC E1EAN Addenda Selection UPC Addenda SelectionMSI Selection Plessey SelectionScanteam 5700 User’s Guide Page Download New Firmware Memory Upload Scanteam 5700 User’s GuideClone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris IBM, Memorex TelexSupported Esprit 200 Ansi AsciiBull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only 5700-X4 Laser Compatible Bar Image +12VDC Input Pin Type D FemaleWand Emulation RS-232 Laser Output Maintenance Cleaning the Scan WindowReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Obtaining Factory Service Welch Allyn, IncWelch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Serial Interface Menu Defaults Output SelectionsGeneral Operating Menu Defaults Keyboard SelectionsSymbology Menu Defaults Industrial Codabar SelectionsCode 11 Selections Symbology Menu Defaults Retail EAN / UPC Addenda SelectionsScanteam 5700 User’s Guide Page Page Page EAN Interleaved 2Matrix 2 Code 2