Hand Held Products Scanteam 5700 User’s Guide, FCC Class B Compliance Statement, A. Statement

Page 3

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Class B Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or television technician for help.

Caution: Any changes or modifications made to this device that are not expressly approved by Welch Allyn, Inc. may void the user’s authority to operate the equipment.

Note: To maintain compliance with FCC Rules and Regulations, cables connected to this device must be shielded cables, in which the cable shield wire(s) have been grounded (tied) to the connector shell.

Canadian Notice

This equipment does not exceed the Class B limits for radio noise emissions as described in the Radio Interference Regulations of the Canadian Department of Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.

C.S.A. Statement

This product must be used with a certified Class 2 power supply or be powered by a certified SELV (Safety Extra Low Voltage) output.

CDRH Statement

This product complies with 21 CFR Part 1040. This product is a Class II (Class IIIa for 5700ALR) laser product with a maximum output of 1.0 mW (1.5 mW for 5700ALR) at 650 nanometers and continuous wave.

SCANTEAM 5700 User’s Guide

Image 3
Contents Decoded Output Disclaimer A. Statement Scanteam 5700 User’s GuideFCC Class B Compliance Statement Canadian NoticePatents Table of Contents Foreign Keyboard Selection Protocol Selection Serial Wedge Output SelectionRequire Data Format Data Format Editor Marker Beam Selection AutoTrigger SelectionKeyboard Function Relationships Supported Interface Keys Industrial Symbology SelectionsObtaining Factory Service Technical Support Maintenance TroubleshootingIntroduction Scanner Identification Model Number 5X00/A-12Cable, Keyboard, and Terminal will vary Connecting the ScannerScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC XT and Compatibles Interface IBM PC AT and Compatibles Interface DefaultIBM PC, Wand Emulation Interface IBM PS/2 and Compatibles InterfaceIBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Notes Dual Interface Programming InstructionsLaser Emulation Selection Code 39 Wand Emulation SelectionSame Code Wand Emulation Selection RS-232 SelectionDual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Suffix Selection Secondary Interface Prefix SelectionExample 4 To Clear a Specific Prefix Entry Example 1 Add Suffix for Specific SymbologyExample 2 Add Suffix for ALL Symbologies Prefix and Suffix ExamplesValue Symbology Code HexOutput Delays Selection Beeper Volume SelectionReread Delay Selection Good Read Delay SelectionLaser Voting Selection Function Code Transmit Selection Buffered Scans SelectionCode I.D. Transmit Selection AIM I.D. Transmit SelectionBaud Rate Selection CTS Check SelectionParity Selection RS-232 Word Length SelectionSerial Wedge Output Selection Protocol Selection➍ Length ➎ Editor Command Sequences➋ Terminal Type ➌ Code I.DData Format Editor Require Data FormatMiscellaneous Commands Send CommandsMove Commands Search CommandsUPC a with 5 digit addenda Data Formatter ExampleScanteam 5700 User’s Guide Introduction AutoTrigger Selection Marker Beam SelectionTransmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection NCR 7052 Keypad Selection AT Direct Connect SelectionKeyboard Style Keyboard Style SelectionsKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Message Length Codabar SelectionCheck Character Append Code 39 SelectionMinimum Maximum Code 93 Selection Full Ascii ChartCheck Digit Interleaved 2 of 5 SelectionMatrix 2 of 5 Selection Code 2 of 5 SelectionCode 128 Selection Code 11 SelectionCode 128 Function Character Selection Code 49 Selection Code 16K SelectionIsbn EAN SelectionUPC E1 UPC SelectionUPC Addenda Selection EAN Addenda SelectionPlessey Selection MSI SelectionScanteam 5700 User’s Guide Page Memory Upload Scanteam 5700 User’s Guide Download New FirmwareClone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris Telex IBM, MemorexAnsi Ascii Supported Esprit 200Bull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only Pin Type D Female 5700-X4 Laser Compatible Bar Image +12VDC InputWand Emulation RS-232 Laser Output Cleaning the Scan Window MaintenanceReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Welch Allyn, Inc Obtaining Factory ServiceWelch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Output Selections Serial Interface Menu DefaultsKeyboard Selections General Operating Menu DefaultsCodabar Selections Symbology Menu Defaults IndustrialCode 11 Selections EAN / UPC Addenda Selections Symbology Menu Defaults RetailScanteam 5700 User’s Guide Page Page Page Code 2 EANInterleaved 2 Matrix 2